Make it easier to locate deadlocked tests

[bblum]

It's really a huge pain to figure out which test is the one that failed or hung, in which case this first half of the line doesn't even get printed.

[brson]

This is because by default when there are multiple cores, the test runner runs tests in parallel, so printing the name of the test, running the test, then printing the result would interleave it with arbitrary junk. If you run with RUST_THREADS=1 the test runner will do what you want and print the test name before running it.

[bblum]

How does it not already interleave? I'd thought a simple st.out.flush() would solve this, but if it wouldn't because of parallel printing, I must be missing something.

[brson]

It's not because of parallel printing (though that is a problem for tests that print to the console). The test runner reports all the results on the same thread, but if it is running them in parallel then they don't finish in the order they are run.

[pnkfelix]

Not critical for 0.6; de-milestoning

[metajack]

Is this the rust test harness, or the test harness that user code uses? If the latter, I think this should be nominated for feature complete.

[alexcrichton]

I think that this is a real issue for tests which possibly hang forever. I think that they way the tests are printed right now is fine (in both the single and multithreaded cases), but the major problem is that tests which hang (in the multithreaded test case) never print anything out.

This is a problem on bors because it's never known which test actually caused the process to hang. I think that the best way to handle this would be to handle signals somehow. If the test harness could catch SIGINT/SIGTERM and terminate all running tests (or at least print out all currently running tests as failures and then exit the process), then at least the source of the failures would be known.

Nominating for the production-ready milestone.

[pnkfelix]

Handling signals is part of #6842.

[graydon]

accepted for production-ready milestone

[pnkfelix]

Accepting for P-low.

[brson]

Ask @alexcrichton about how to fix this.

[steveklabnik]

Triage: still the same today.

[bagedevimo]

I'd like to take a look at this, @alexcrichton, did you have a suggestion as to how to begin?

[alexcrichton]

@bagedevimo unfortunately I don't know of a great way to solve this, but I can at least describe the problem!

The crux of the problem here is that tests which deadlock or for some other reason don't finish never print anything by default, which means it's very difficult to debug what's going on if the test suite times out (e.g. is killed by an external process). Tests are by default run in multiple threads which is why we don't print partial output.

Some possible solutions for this could be:

• Use a library to have fancy control over terminal output, and make a better UI on top of that. For example you could have a status bar of all tests that have completed and then a line-per-thread which shows the status of the thread (e.g. if it's idle, what test it's running, etc). The terminal would then all get updated whenever anything completed. This is pretty fancy, however, and is unlikely to be fit for this repository itself unfortunately.
• Set a timeout such that if no tests have completed after running for N seconds, the currently running tests are all printed to stdout. Either that or if any test itself is taking longer than 5 seconds, the test is printed to stdout. This would at least provide a status message which can be scraped to see what tests are running. This is unfortunately not very useful, however, if the test then later completes as it's just confusing output at that point.
• A signal handler could be installed to catch termination of the test suite itself. This signal handler would then indicate to the test suite that it should print out all actively running tests and then exit. The hard part about this is (A) you have to deal with signal handlers and (B) it's unclear how well this would work on Windows (I don't think it would work for the buildbot case, but may work for the ctrl-c-at-terminal case).

My personal preference about how to tackle this would be to develop an awesome terminal-ui-test-runner externally so we can see how great it is, and then push really hard on custom test frameworks in Rust to ensure that the experience in using it is super smooth as well.

Sorry if that's not quite a concrete way of how to tackle this, but hopefully it's at least a start!