Fix GPIO Kconfig bug & add BT host driver by apopple · Pull Request #1 · openbmc/linux

apopple · 2015-09-29T05:26:50Z

No description provided.

The Aspeed GPIO menu entry was added under "PCI GPIO expanders" which depends on PCI which may not be enabled for Aspeed. Move the entry to the "Memory mapped GPIO drivers" which describes the Aspeed GPIO driver more correctly. Signed-off-by: Alistair Popple <alistair@popple.id.au>

This patch adds a simple device driver to expose the iBT interface on Aspeed chips as a character device (/dev/bt). Signed-off-by: Alistair Popple <alistair@popple.id.au>

…ap_device_late_init Kernel fails to boot 50% of times (form build to build) with RT-patchset applied due to the following race - on late boot stages deferred_probe_work_func->omap_hsmmc_probe races with omap_device_late_ini. The same issue has been reported now on linux-next (4.3) by Keerthy [1] late_initcall - deferred_probe_initcal() tries to re-probe all pending driver's probe. - later on, some driver is probing in this case It's cpsw.c (but could be any other drivers) cpsw_init - platform_driver_register - really_probe - driver_bound - driver_deferred_probe_trigger and boot proceed. So, at this moment we have deferred_probe_work_func scheduled. late_initcall_sync - omap_device_late_init - omap_device_idle CPU1 CPU2 - deferred_probe_work_func - really_probe - omap_hsmmc_probe - pm_runtime_get_sync late_initcall_sync - omap_device_late_init if (od->_driver_status != BUS_NOTIFY_BOUND_DRIVER) { if (od->_state == OMAP_DEVICE_STATE_ENABLED) { - omap_device_idle [ops - IP is disabled] - [fail] - pm_runtime_put_sync - omap_hsmmc_runtime_suspend [ooops!] == log == omap_hsmmc 480b4000.mmc: unable to get vmmc regulator -517 davinci_mdio 48485000.mdio: davinci mdio revision 1.6 davinci_mdio 48485000.mdio: detected phy mask fffffff3 libphy: 48485000.mdio: probed davinci_mdio 48485000.mdio: phy[2]: device 48485000.mdio:02, driver unknown davinci_mdio 48485000.mdio: phy[3]: device 48485000.mdio:03, driver unknown omap_hsmmc 480b4000.mmc: unable to get vmmc regulator -517 cpsw 48484000.ethernet: Detected MACID = b4:99:4c:c7:d2:48 cpsw 48484000.ethernet: cpsw: Detected MACID = b4:99:4c:c7:d2:49 hctosys: unable to open rtc device (rtc0) omap_hsmmc 480b4000.mmc: omap_device_late_idle: enabled but no driver. Idling ldousb: disabling Unhandled fault: imprecise external abort (0x1406) at 0x00000000 [00000000] *pgd=00000000 Internal error: : 1406 [#1] PREEMPT SMP ARM Modules linked in: CPU: 1 PID: 58 Comm: kworker/u4:1 Not tainted 4.1.2-rt1-00467-g6da3c0a-dirty #5 Hardware name: Generic DRA74X (Flattened Device Tree) Workqueue: deferwq deferred_probe_work_func task: ee6ddb00 ti: edd3c000 task.ti: edd3c000 PC is at omap_hsmmc_runtime_suspend+0x1c/0x12c LR is at _od_runtime_suspend+0xc/0x24 pc : [<c0471998>] lr : [<c0029590>] psr: a0000013 sp : edd3dda0 ip : ee6ddb00 fp : c07be540 r10: 00000000 r9 : c07be540 r8 : 00000008 r7 : 00000000 r6 : ee646c10 r5 : ee646c10 r4 : edd79380 r3 : fa0b4100 r2 : 00000000 r1 : 00000000 r0 : ee646c10 Flags: NzCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment kernel Control: 10c5387d Table: 8000406 DAC: 00000015 Process kworker/u4:1 (pid: 58, stack limit = 0xedd3c218) Stack: (0xedd3dda0 to 0xedd3e000) dda0: ee646c70 ee646c10 c0029584 00000000 00000008 c0029590 ee646c70 ee646c10 ddc0: c0029584 c03adfb8 ee646c10 00000004 0000000c c03adff0 ee646c10 00000004 dde0: 0000000c c03ae4ec 00000000 edd3c000 ee646c10 00000004 ee646c70 00000004 de00: fa0b4000 c03aec20 ee6ddb00 ee646c10 00000004 ee646c70 ee646c10 fffffdfb de20: edd79380 00000000 fa0b4000 c03aee90 fffffdfb edd79000 ee646c00 c0474290 de40: 00000000 edda24c0 edd79380 edc81f00 00000000 00000200 00000001 c06dd488 de60: edda3960 ee646c10 ee646c10 c0824cc4 fffffdfb c0880c94 00000002 edc92600 de80: c0836378 c03a7f84 ee646c10 c0824cc4 00000000 c0880c80 c0880c94 c03a6568 dea0: 00000000 ee646c10 c03a66ac ee4f8000 00000000 00000001 edc92600 c03a4b40 dec0: ee404c94 edc83c4c ee646c10 ee646c10 ee646c4 c03a63c4 ee646c10 ee646c10 dee0: c0814448 c03a5aa8 ee646c10 c0814220 edd3c000 c03a5ec0 c0814250 ee6be400 df00: edd3c000 c004e5b ee6ddb01 00000078 ee6ddb00 ee4f8000 ee6be418 edd3c000 df20: ee4f8028 00000088 c0836045 ee4f8000 ee6be400 c004e928 ee4f8028 00000000 df40: c004e8ec 00000000 ee6bf1c0 ee6be400 c004e8ec 00000000 00000000 00000000 df60: 00000000 c0053450 2e56fa97 00000000 afdffbd7 ee6be400 00000000 00000000 df80: edd3df80 edd3df80 00000000 00000000 edd3df9 edd3df9 edd3dfac ee6bf1c0 dfa0: c0053384 00000000 00000000 c000f668 00000000 00000000 00000000 00000000 dfc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 dfe0: 00000000 00000000 00000000 00000000 00000013 00000000 f1fc9d7e febfbdff [<c0471998>] (omap_hsmmc_runtime_suspend) from [<c0029590>] (_od_runtime_suspend+0xc/0x24) [<c0029590>] (_od_runtime_suspend) from [<c03adfb8>] (__rpm_callback+0x24/0x3c) [<c03adfb8>] (__rpm_callback) from [<c03adff0>] (rpm_callback+0x20/0x80) [<c03adff0>] (rpm_callback) from [<c03ae4ec>] (rpm_suspend+0xe4/0x618) [<c03ae4ec>] (rpm_suspend) from [<c03aee90>] (__pm_runtime_idle+0x60/0x80) [<c03aee90>] (__pm_runtime_idle) from [<c0474290>] (omap_hsmmc_probe+0x6bc/0xa7c) [<c0474290>] (omap_hsmmc_probe) from [<c03a7f84>] (platform_drv_probe+0x44/0xa4) [<c03a7f84>] (platform_drv_probe) from [<c03a6568>] (driver_probe_device+0x170/0x2b4) [<c03a6568>] (driver_probe_device) from [<c03a4b40>] (bus_for_each_drv+0x64/0x98) [<c03a4b40>] (bus_for_each_drv) from [<c03a63c4>] (device_attach+0x70/0x88) [<c03a63c4>] (device_attach) from [<c03a5aa8>] (bus_probe_device+0x84/0xac) [<c03a5aa8>] (bus_probe_device) from [<c03a5ec0>] (deferred_probe_work_func+0x58/0x88) [<c03a5ec0>] (deferred_probe_work_func) from [<c004e5bc>] (process_one_work+0x134/0x464) [<c004e5bc>] (process_one_work) from [<c004e928>] (worker_thread+0x3c/0x4fc) [<c004e928>] (worker_thread) from [<c0053450>] (kthread+0xcc/0xe4) [<c0053450>] (kthread) from [<c000f668>] (ret_from_fork+0x14/0x2c) Code: e594302c e593202c e584205c e594302c (e5932128) ---[ end trace 0000000000000002 ]--- The issue happens because omap_device_late_init() do not take into account that some drivers are present, but their probes were not finished successfully and where deferred instead. This is the valid case, and omap_device_late_init() should not idle such devices. To fix this issue, the value of omap_device->_driver_status field should be checked not only for BUS_NOTIFY_BOUND_DRIVER (driver is present and has been bound to device successfully), but also checked for BUS_NOTIFY_BIND_DRIVER (driver about to be bound) - which means driver is present and there was try to bind it to device. [1] http://www.spinics.net/lists/arm-kernel/msg441880.html Cc: Tero Kristo <t-kristo@ti.com> Cc: Keerthy <j-keerthy@ti.com> Tested-by: Keerthy <j-keerthy@ti.com> Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>

On old ARM chips, unaligned accesses to memory are not trapped and fixed. On module load, symbols are relocated, and the relocation of __bug_table symbols is done on a u32 basis. Yet the section is not aligned to a multiple of 4 address, but to a multiple of 2. This triggers an Oops on pxa architecture, where address 0xbf0021ea is the first relocation in the __bug_table section : apply_relocate(): pxa3xx_nand: section 13 reloc 0 sym '' Unable to handle kernel paging request at virtual address bf0021ea pgd = e1cd0000 [bf0021ea] *pgd=c1cce851, *pte=c1cde04f, *ppte=c1cde01f Internal error: Oops: 23 [#1] ARM Modules linked in: CPU: 0 PID: 606 Comm: insmod Not tainted 4.2.0-rc8-next-20150828-cm-x300+ torvalds#887 Hardware name: CM-X300 module task: e1c68700 ti: e1c3e000 task.ti: e1c3e000 PC is at apply_relocate+0x2f4/0x3d4 LR is at 0xbf0021ea pc : [<c000e7c8>] lr : [<bf0021ea>] psr: 80000013 sp : e1c3fe30 ip : 60000013 fp : e49e8c60 r10: e49e8fa8 r9 : 00000000 r8 : e49e7c58 r7 : e49e8c38 r6 : e49e8a58 r5 : e49e8920 r4 : e49e8918 r3 : bf0021ea r2 : bf007034 r1 : 00000000 r0 : bf000000 Flags: Nzcv IRQs on FIQs on Mode SVC_32 ISA ARM Segment none Control: 0000397f Table: c1cd0018 DAC: 00000051 Process insmod (pid: 606, stack limit = 0xe1c3e198) [<c000e7c8>] (apply_relocate) from [<c005ce5c>] (load_module+0x1248/0x1f5c) [<c005ce5c>] (load_module) from [<c005dc54>] (SyS_init_module+0xe4/0x170) [<c005dc54>] (SyS_init_module) from [<c000a420>] (ret_fast_syscall+0x0/0x38) Fix this by ensuring entries in __bug_table are all aligned to at least of multiple of 4. This transforms a module section __bug_table as : - [12] __bug_table PROGBITS 00000000 002232 000018 00 A 0 0 1 + [12] __bug_table PROGBITS 00000000 002232 000018 00 A 0 0 4 Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr> Reviewed-by: Dave Martin <Dave.Martin@arm.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

The renesas-irqc interrupt controller is cascaded to the GIC. Hence when propagating wake-up settings to its parent interrupt controller, the following lockdep warning is printed: ============================================= [ INFO: possible recursive locking detected ] 4.2.0-ape6evm-10725-g50fcd7643c034198 torvalds#280 Not tainted --------------------------------------------- s2ram/1072 is trying to acquire lock: (&irq_desc_lock_class){-.-...}, at: [<c008d3fc>] __irq_get_desc_lock+0x58/0x98 but task is already holding lock: (&irq_desc_lock_class){-.-...}, at: [<c008d3fc>] __irq_get_desc_lock+0x58/0x98 other info that might help us debug this: Possible unsafe locking scenario: CPU0 ---- lock(&irq_desc_lock_class); lock(&irq_desc_lock_class); *** DEADLOCK *** May be due to missing lock nesting notation 6 locks held by s2ram/1072: #0: (sb_writers#7){.+.+.+}, at: [<c012eb14>] __sb_start_write+0xa0/0xa8 #1: (&of->mutex){+.+.+.}, at: [<c019396c>] kernfs_fop_write+0x4c/0x1bc #2: (s_active#24){.+.+.+}, at: [<c0193974>] kernfs_fop_write+0x54/0x1bc #3: (pm_mutex){+.+.+.}, at: [<c008213c>] pm_suspend+0x10c/0x510 #4: (&dev->mutex){......}, at: [<c02af3c4>] __device_suspend+0xdc/0x2cc #5: (&irq_desc_lock_class){-.-...}, at: [<c008d3fc>] __irq_get_desc_lock+0x58/0x98 stack backtrace: CPU: 0 PID: 1072 Comm: s2ram Not tainted 4.2.0-ape6evm-10725-g50fcd7643c034198 torvalds#280 Hardware name: Generic R8A73A4 (Flattened Device Tree) [<c0018078>] (unwind_backtrace) from [<c00144f0>] (show_stack+0x10/0x14) [<c00144f0>] (show_stack) from [<c0451f14>] (dump_stack+0x88/0x98) [<c0451f14>] (dump_stack) from [<c007b29c>] (__lock_acquire+0x15cc/0x20e4) [<c007b29c>] (__lock_acquire) from [<c007c6e0>] (lock_acquire+0xac/0x12c) [<c007c6e0>] (lock_acquire) from [<c0457c00>] (_raw_spin_lock_irqsave+0x40/0x54) [<c0457c00>] (_raw_spin_lock_irqsave) from [<c008d3fc>] (__irq_get_desc_lock+0x58/0x98) [<c008d3fc>] (__irq_get_desc_lock) from [<c008ebbc>] (irq_set_irq_wake+0x20/0xf8) [<c008ebbc>] (irq_set_irq_wake) from [<c0260770>] (irqc_irq_set_wake+0x20/0x4c) [<c0260770>] (irqc_irq_set_wake) from [<c008ec28>] (irq_set_irq_wake+0x8c/0xf8) [<c008ec28>] (irq_set_irq_wake) from [<c02cb8c0>] (gpio_keys_suspend+0x74/0xc0) [<c02cb8c0>] (gpio_keys_suspend) from [<c02ae8cc>] (dpm_run_callback+0x54/0x124) Avoid this false positive by using a separate lockdep class for IRQC interrupts. Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Cc: Grygorii Strashko <grygorii.strashko@ti.com> Cc: Magnus Damm <magnus.damm@gmail.com> Cc: Jason Cooper <jason@lakedaemon.net> Link: http://lkml.kernel.org/r/1441798974-25716-2-git-send-email-geert%2Brenesas@glider.be Signed-off-by: Thomas Gleixner <tglx@linutronix.de>

The renesas-intc-irqpin interrupt controller is cascaded to the GIC. Hence when propagating wake-up settings to its parent interrupt controller, the following lockdep warning is printed: ============================================= [ INFO: possible recursive locking detected ] 4.2.0-armadillo-10725-g50fcd7643c034198 torvalds#781 Not tainted --------------------------------------------- s2ram/1179 is trying to acquire lock: (&irq_desc_lock_class){-.-...}, at: [<c005bb54>] __irq_get_desc_lock+0x78/0x94 but task is already holding lock: (&irq_desc_lock_class){-.-...}, at: [<c005bb54>] __irq_get_desc_lock+0x78/0x94 other info that might help us debug this: Possible unsafe locking scenario: CPU0 ---- lock(&irq_desc_lock_class); lock(&irq_desc_lock_class); *** DEADLOCK *** May be due to missing lock nesting notation 7 locks held by s2ram/1179: #0: (sb_writers#7){.+.+.+}, at: [<c00c9708>] __sb_start_write+0x64/0xb8 #1: (&of->mutex){+.+.+.}, at: [<c0125a00>] kernfs_fop_write+0x78/0x1a0 #2: (s_active#23){.+.+.+}, at: [<c0125a08>] kernfs_fop_write+0x80/0x1a0 #3: (autosleep_lock){+.+.+.}, at: [<c0058244>] pm_autosleep_lock+0x18/0x20 #4: (pm_mutex){+.+.+.}, at: [<c0057e50>] pm_suspend+0x54/0x248 #5: (&dev->mutex){......}, at: [<c0243a20>] __device_suspend+0xdc/0x240 #6: (&irq_desc_lock_class){-.-...}, at: [<c005bb54>] __irq_get_desc_lock+0x78/0x94 stack backtrace: CPU: 0 PID: 1179 Comm: s2ram Not tainted 4.2.0-armadillo-10725-g50fcd7643c034198 Hardware name: Generic R8A7740 (Flattened Device Tree) [<c00129f4>] (dump_backtrace) from [<c0012bec>] (show_stack+0x18/0x1c) [<c0012bd4>] (show_stack) from [<c03f5d94>] (dump_stack+0x20/0x28) [<c03f5d74>] (dump_stack) from [<c00514d4>] (__lock_acquire+0x67c/0x1b88) [<c0050e58>] (__lock_acquire) from [<c0052df8>] (lock_acquire+0x9c/0xbc) [<c0052d5c>] (lock_acquire) from [<c03fb068>] (_raw_spin_lock_irqsave+0x44/0x58) [<c03fb024>] (_raw_spin_lock_irqsave) from [<c005bb54>] (__irq_get_desc_lock+0x78/0x94 [<c005badc>] (__irq_get_desc_lock) from [<c005c3d8>] (irq_set_irq_wake+0x28/0x100) [<c005c3b0>] (irq_set_irq_wake) from [<c01e50d0>] (intc_irqpin_irq_set_wake+0x24/0x4c) [<c01e50ac>] (intc_irqpin_irq_set_wake) from [<c005c17c>] (set_irq_wake_real+0x3c/0x50 [<c005c140>] (set_irq_wake_real) from [<c005c414>] (irq_set_irq_wake+0x64/0x100) [<c005c3b0>] (irq_set_irq_wake) from [<c02a19b4>] (gpio_keys_suspend+0x60/0xa0) [<c02a1954>] (gpio_keys_suspend) from [<c023b750>] (platform_pm_suspend+0x3c/0x5c) Avoid this false positive by using a separate lockdep class for INTC External IRQ Pin interrupts. Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Cc: Grygorii Strashko <grygorii.strashko@ti.com> Cc: Magnus Damm <magnus.damm@gmail.com> Cc: Jason Cooper <jason@lakedaemon.net> Link: http://lkml.kernel.org/r/1441798974-25716-3-git-send-email-geert%2Brenesas@glider.be Signed-off-by: Thomas Gleixner <tglx@linutronix.de>

The OPP list needs to be protected against concurrent accesses. Using simple RCU read locks does the trick and gets rid of the following lockdep warning: =============================== [ INFO: suspicious RCU usage. ] 4.2.0-next-20150908 #1 Not tainted ------------------------------- drivers/base/power/opp.c:460 Missing rcu_read_lock() or dev_opp_list_lock protection! other info that might help us debug this: rcu_scheduler_active = 1, debug_locks = 0 4 locks held by kworker/u8:0/6: #0: ("%s""deferwq"){++++.+}, at: [<c0040d8c>] process_one_work+0x118/0x4bc #1: (deferred_probe_work){+.+.+.}, at: [<c0040d8c>] process_one_work+0x118/0x4bc #2: (&dev->mutex){......}, at: [<c03b8194>] __device_attach+0x20/0x118 #3: (prepare_lock){+.+...}, at: [<c054bc08>] clk_prepare_lock+0x10/0xf8 stack backtrace: CPU: 2 PID: 6 Comm: kworker/u8:0 Not tainted 4.2.0-next-20150908 #1 Hardware name: NVIDIA Tegra SoC (Flattened Device Tree) Workqueue: deferwq deferred_probe_work_func [<c001802c>] (unwind_backtrace) from [<c00135a4>] (show_stack+0x10/0x14) [<c00135a4>] (show_stack) from [<c02a8418>] (dump_stack+0x94/0xd4) [<c02a8418>] (dump_stack) from [<c03c6f6c>] (dev_pm_opp_find_freq_ceil+0x108/0x114) [<c03c6f6c>] (dev_pm_opp_find_freq_ceil) from [<c0551a3c>] (dfll_calculate_rate_request+0xb8/0x170) [<c0551a3c>] (dfll_calculate_rate_request) from [<c0551b10>] (dfll_clk_round_rate+0x1c/0x2c) [<c0551b10>] (dfll_clk_round_rate) from [<c054de2c>] (clk_calc_new_rates+0x1b8/0x228) [<c054de2c>] (clk_calc_new_rates) from [<c054e44c>] (clk_core_set_rate_nolock+0x44/0xac) [<c054e44c>] (clk_core_set_rate_nolock) from [<c054e4d8>] (clk_set_rate+0x24/0x34) [<c054e4d8>] (clk_set_rate) from [<c0512460>] (tegra124_cpufreq_probe+0x120/0x230) [<c0512460>] (tegra124_cpufreq_probe) from [<c03b9cbc>] (platform_drv_probe+0x44/0xac) [<c03b9cbc>] (platform_drv_probe) from [<c03b84c8>] (driver_probe_device+0x218/0x304) [<c03b84c8>] (driver_probe_device) from [<c03b69b0>] (bus_for_each_drv+0x60/0x94) [<c03b69b0>] (bus_for_each_drv) from [<c03b8228>] (__device_attach+0xb4/0x118) ata1: SATA link down (SStatus 0 SControl 300) [<c03b8228>] (__device_attach) from [<c03b77c8>] (bus_probe_device+0x88/0x90) [<c03b77c8>] (bus_probe_device) from [<c03b7be8>] (deferred_probe_work_func+0x58/0x8c) [<c03b7be8>] (deferred_probe_work_func) from [<c0040dfc>] (process_one_work+0x188/0x4bc) [<c0040dfc>] (process_one_work) from [<c004117c>] (worker_thread+0x4c/0x4f4) [<c004117c>] (worker_thread) from [<c0047230>] (kthread+0xe4/0xf8) [<c0047230>] (kthread) from [<c000f7d0>] (ret_from_fork+0x14/0x24) Signed-off-by: Thierry Reding <treding@nvidia.com> Fixes: c4fe70a ("clk: tegra: Add closed loop support for the DFLL") [vince.h@nvidia.com: Unlock rcu on error path] Signed-off-by: Vince Hsu <vince.h@nvidia.com> [sboyd@codeaurora.org: Dropped second hunk that nested the rcu read lock unnecessarily] Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>

If filelayout_decode_layout fail, _filelayout_free_lseg will causes a double freeing of fh_array. [ 1179.279800] BUG: unable to handle kernel NULL pointer dereference at (null) [ 1179.280198] IP: [<ffffffffa027222d>] filelayout_free_fh_array.isra.11+0x1d/0x70 [nfs_layout_nfsv41_files] [ 1179.281010] PGD 0 [ 1179.281443] Oops: 0000 [#1] [ 1179.281831] Modules linked in: nfs_layout_nfsv41_files(OE) nfsv4(OE) nfs(OE) fscache(E) xfs libcrc32c coretemp nfsd crct10dif_pclmul ppdev crc32_pclmul crc32c_intel auth_rpcgss ghash_clmulni_intel nfs_acl lockd vmw_balloon grace sunrpc parport_pc vmw_vmci parport shpchp i2c_piix4 vmwgfx drm_kms_helper ttm drm serio_raw mptspi scsi_transport_spi mptscsih e1000 mptbase ata_generic pata_acpi [last unloaded: fscache] [ 1179.283891] CPU: 0 PID: 13336 Comm: cat Tainted: G OE 4.3.0-rc1-pnfs+ torvalds#244 [ 1179.284323] Hardware name: VMware, Inc. VMware Virtual Platform/440BX Desktop Reference Platform, BIOS 6.00 05/20/2014 [ 1179.285206] task: ffff8800501d48c0 ti: ffff88003e3c4000 task.ti: ffff88003e3c4000 [ 1179.285668] RIP: 0010:[<ffffffffa027222d>] [<ffffffffa027222d>] filelayout_free_fh_array.isra.11+0x1d/0x70 [nfs_layout_nfsv41_files] [ 1179.286612] RSP: 0018:ffff88003e3c77f8 EFLAGS: 00010202 [ 1179.287092] RAX: 0000000000000000 RBX: ffff88001fe78900 RCX: 0000000000000000 [ 1179.287731] RDX: ffffea0000f40760 RSI: ffff88001fe789c8 RDI: ffff88001fe789c0 [ 1179.288383] RBP: ffff88003e3c7810 R08: ffffea0000f40760 R09: 0000000000000000 [ 1179.289170] R10: 0000000000000000 R11: 0000000000000001 R12: ffff88001fe789c8 [ 1179.289959] R13: ffff88001fe789c0 R14: ffff88004ec05a80 R15: ffff88004f935b88 [ 1179.290791] FS: 00007f4e66bb5700(0000) GS:ffffffff81c29000(0000) knlGS:0000000000000000 [ 1179.291580] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 1179.292209] CR2: 0000000000000000 CR3: 00000000203f8000 CR4: 00000000001406f0 [ 1179.292731] Stack: [ 1179.293195] ffff88001fe78900 00000000000000d0 ffff88001fe78178 ffff88003e3c7868 [ 1179.293676] ffffffffa0272737 0000000000000001 0000000000000001 ffff88001fe78800 [ 1179.294151] 00000000614fffce ffffffff81727671 ffff88001fe78100 ffff88001fe78100 [ 1179.294623] Call Trace: [ 1179.295092] [<ffffffffa0272737>] filelayout_alloc_lseg+0xa7/0x2d0 [nfs_layout_nfsv41_files] [ 1179.295625] [<ffffffff81727671>] ? out_of_line_wait_on_bit+0x81/0xb0 [ 1179.296133] [<ffffffffa040407e>] pnfs_layout_process+0xae/0x320 [nfsv4] [ 1179.296632] [<ffffffffa03e0a01>] nfs4_proc_layoutget+0x2b1/0x360 [nfsv4] [ 1179.297134] [<ffffffffa0402983>] pnfs_update_layout+0x853/0xb30 [nfsv4] [ 1179.297632] [<ffffffffa039db24>] ? nfs_get_lock_context+0x74/0x170 [nfs] [ 1179.298158] [<ffffffffa0271807>] filelayout_pg_init_read+0x37/0x50 [nfs_layout_nfsv41_files] [ 1179.298834] [<ffffffffa03a72d9>] __nfs_pageio_add_request+0x119/0x460 [nfs] [ 1179.299385] [<ffffffffa03a6bd7>] ? nfs_create_request.part.9+0x37/0x2e0 [nfs] [ 1179.299872] [<ffffffffa03a7cc3>] nfs_pageio_add_request+0xa3/0x1b0 [nfs] [ 1179.300362] [<ffffffffa03a8635>] readpage_async_filler+0x85/0x260 [nfs] [ 1179.300907] [<ffffffff81180cb1>] read_cache_pages+0x91/0xd0 [ 1179.301391] [<ffffffffa03a85b0>] ? nfs_read_completion+0x220/0x220 [nfs] [ 1179.301867] [<ffffffffa03a8dc8>] nfs_readpages+0x128/0x200 [nfs] [ 1179.302330] [<ffffffff81180ef3>] __do_page_cache_readahead+0x203/0x280 [ 1179.302784] [<ffffffff81180dc8>] ? __do_page_cache_readahead+0xd8/0x280 [ 1179.303413] [<ffffffff81181116>] ondemand_readahead+0x1a6/0x2f0 [ 1179.303855] [<ffffffff81181371>] page_cache_sync_readahead+0x31/0x50 [ 1179.304286] [<ffffffff811750a6>] generic_file_read_iter+0x4a6/0x5c0 [ 1179.304711] [<ffffffffa03a0316>] ? __nfs_revalidate_mapping+0x1f6/0x240 [nfs] [ 1179.305132] [<ffffffffa039ccf2>] nfs_file_read+0x52/0xa0 [nfs] [ 1179.305540] [<ffffffff811e343c>] __vfs_read+0xcc/0x100 [ 1179.305936] [<ffffffff811e3d15>] vfs_read+0x85/0x130 [ 1179.306326] [<ffffffff811e4a98>] SyS_read+0x58/0xd0 [ 1179.306708] [<ffffffff8172caaf>] entry_SYSCALL_64_fastpath+0x12/0x76 [ 1179.307094] Code: c4 66 66 66 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 44 00 00 55 48 89 e5 41 55 41 54 53 8b 07 49 89 f4 85 c0 74 47 48 8b 06 49 89 fd <48> 8b 38 48 85 ff 74 22 31 db eb 0c 48 63 d3 48 8b 3c d0 48 85 [ 1179.308357] RIP [<ffffffffa027222d>] filelayout_free_fh_array.isra.11+0x1d/0x70 [nfs_layout_nfsv41_files] [ 1179.309177] RSP <ffff88003e3c77f8> [ 1179.309582] CR2: 0000000000000000 Signed-off-by: Kinglong Mee <kinglongmee@gmail.com> Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>

If we didn't call ATMARP_MKIP before ATMARP_ENCAP the VCC descriptor is non-existant and we'll end up dereferencing a NULL ptr: [1033173.491930] kasan: GPF could be caused by NULL-ptr deref or user memory accessirq event stamp: 123386 [1033173.493678] general protection fault: 0000 [#1] PREEMPT SMP DEBUG_PAGEALLOC KASAN [1033173.493689] Modules linked in: [1033173.493697] CPU: 9 PID: 23815 Comm: trinity-c64 Not tainted 4.2.0-next-20150911-sasha-00043-g353d875-dirty #2545 [1033173.493706] task: ffff8800630c4000 ti: ffff880063110000 task.ti: ffff880063110000 [1033173.493823] RIP: clip_ioctl (net/atm/clip.c:320 net/atm/clip.c:689) [1033173.493826] RSP: 0018:ffff880063117a88 EFLAGS: 00010203 [1033173.493828] RAX: dffffc0000000000 RBX: 0000000000000000 RCX: 000000000000000c [1033173.493830] RDX: 0000000000000002 RSI: ffffffffb3f10720 RDI: 0000000000000014 [1033173.493832] RBP: ffff880063117b80 R08: ffff88047574d9a4 R09: 0000000000000000 [1033173.493834] R10: 0000000000000000 R11: 0000000000000000 R12: 1ffff1000c622f53 [1033173.493836] R13: ffff8800cb905500 R14: ffff8808d6da2000 R15: 00000000fffffdfd [1033173.493840] FS: 00007fa56b92d700(0000) GS:ffff880478000000(0000) knlGS:0000000000000000 [1033173.493843] CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b [1033173.493845] CR2: 0000000000000000 CR3: 00000000630e8000 CR4: 00000000000006a0 [1033173.493855] Stack: [1033173.493862] ffffffffb0b60444 000000000000eaea 0000000041b58ab3 ffffffffb3c3ce32 [1033173.493867] ffffffffb0b6f3e0 ffffffffb0b60444 ffffffffb5ea2e50 1ffff1000c622f5e [1033173.493873] ffff8800630c4cd8 00000000000ee09a ffffffffb3ec4888 ffffffffb5ea2de8 [1033173.493874] Call Trace: [1033173.494108] do_vcc_ioctl (net/atm/ioctl.c:170) [1033173.494113] vcc_ioctl (net/atm/ioctl.c:189) [1033173.494116] svc_ioctl (net/atm/svc.c:605) [1033173.494200] sock_do_ioctl (net/socket.c:874) [1033173.494204] sock_ioctl (net/socket.c:958) [1033173.494244] do_vfs_ioctl (fs/ioctl.c:43 fs/ioctl.c:607) [1033173.494290] SyS_ioctl (fs/ioctl.c:622 fs/ioctl.c:613) [1033173.494295] entry_SYSCALL_64_fastpath (arch/x86/entry/entry_64.S:186) [1033173.494362] Code: fa 48 c1 ea 03 80 3c 02 00 0f 85 50 09 00 00 49 8b 9e 60 06 00 00 48 b8 00 00 00 00 00 fc ff df 48 8d 7b 14 48 89 fa 48 c1 ea 03 <0f> b6 04 02 48 89 fa 83 e2 07 38 d0 7f 08 84 c0 0f 85 14 09 00 All code ======== 0: fa cli 1: 48 c1 ea 03 shr $0x3,%rdx 5: 80 3c 02 00 cmpb $0x0,(%rdx,%rax,1) 9: 0f 85 50 09 00 00 jne 0x95f f: 49 8b 9e 60 06 00 00 mov 0x660(%r14),%rbx 16: 48 b8 00 00 00 00 00 movabs $0xdffffc0000000000,%rax 1d: fc ff df 20: 48 8d 7b 14 lea 0x14(%rbx),%rdi 24: 48 89 fa mov %rdi,%rdx 27: 48 c1 ea 03 shr $0x3,%rdx 2b:* 0f b6 04 02 movzbl (%rdx,%rax,1),%eax <-- trapping instruction 2f: 48 89 fa mov %rdi,%rdx 32: 83 e2 07 and $0x7,%edx 35: 38 d0 cmp %dl,%al 37: 7f 08 jg 0x41 39: 84 c0 test %al,%al 3b: 0f 85 14 09 00 00 jne 0x955 Code starting with the faulting instruction =========================================== 0: 0f b6 04 02 movzbl (%rdx,%rax,1),%eax 4: 48 89 fa mov %rdi,%rdx 7: 83 e2 07 and $0x7,%edx a: 38 d0 cmp %dl,%al c: 7f 08 jg 0x16 e: 84 c0 test %al,%al 10: 0f 85 14 09 00 00 jne 0x92a [1033173.494366] RIP clip_ioctl (net/atm/clip.c:320 net/atm/clip.c:689) [1033173.494368] RSP <ffff880063117a88> Signed-off-by: Sasha Levin <sasha.levin@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>

Commit b6d3096 (Input: uinput - switch to using for_each_set_bit()) switched driver to use for_each_set_bit(). However during initial write of the uinput structure that contains min/max data for all possible axes none of them are reflected in dev->absbit yet and so we were skipping over all of them and were not allocating absinfo memory which caused crash later when driver tried to sens EV_ABS events: <1>[ 15.064330] BUG: unable to handle kernel NULL pointer dereference at 0000000000000024 <1>[ 15.064336] IP: [<ffffffff8163f142>] input_handle_event+0x232/0x4e0 <4>[ 15.064343] PGD 0 <4>[ 15.064345] Oops: 0000 [#1] SMP Fixes: b6d3096 Cc: stable@vger.kernel.org Reported-by: Stephen Chandler Paul <cpaul@redhat.com> Tested-by: Stephen Chandler Paul <cpaul@redhat.com> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

A deadlock trace is seen in netcp driver with lockup detector enabled. The trace log is provided below for reference. This patch fixes the bug by removing the usage of netcp_modules_lock within ndo_ops functions. ndo_{open/close/ioctl)() is already called with rtnl_lock held. So there is no need to hold another mutex for serialization across processes on multiple cores. So remove use of netcp_modules_lock mutex from these ndo ops functions. ndo_set_rx_mode() shouldn't be using a mutex as it is called from atomic context. In the case of ndo_set_rx_mode(), there can be call to this API without rtnl_lock held from an atomic context. As the underlying modules are expected to add address to a hardware table, it is to be protected across concurrent updates and hence a spin lock is used to synchronize the access. Same with ndo_vlan_rx_add_vid() & ndo_vlan_rx_kill_vid(). Probably the netcp_modules_lock is used to protect the module not being removed as part of rmmod. Currently this is not fully implemented and assumes the interface is brought down before doing rmmod of modules. The support for rmmmod while interface is up is expected in a future patch set when additional modules such as pa, qos are added. For now all of the tests such as if up/down, reboot, iperf works fine with this patch applied. Deadlock trace seen with lockup detector enabled is shown below for reference. [ 16.863014] ====================================================== [ 16.869183] [ INFO: possible circular locking dependency detected ] [ 16.875441] 4.1.6-01265-gfb1e101 #1 Tainted: G W [ 16.881176] ------------------------------------------------------- [ 16.887432] ifconfig/1662 is trying to acquire lock: [ 16.892386] (netcp_modules_lock){+.+.+.}, at: [<c03e8110>] netcp_ndo_open+0x168/0x518 [ 16.900321] [ 16.900321] but task is already holding lock: [ 16.906144] (rtnl_mutex){+.+.+.}, at: [<c053a418>] devinet_ioctl+0xf8/0x7e4 [ 16.913206] [ 16.913206] which lock already depends on the new lock. [ 16.913206] [ 16.921372] [ 16.921372] the existing dependency chain (in reverse order) is: [ 16.928844] -> #1 (rtnl_mutex){+.+.+.}: [ 16.932865] [<c06023f0>] mutex_lock_nested+0x68/0x4a8 [ 16.938521] [<c04c5758>] register_netdev+0xc/0x24 [ 16.943831] [<c03e65c0>] netcp_module_probe+0x214/0x2ec [ 16.949660] [<c03e8a54>] netcp_register_module+0xd4/0x140 [ 16.955663] [<c089654c>] keystone_gbe_init+0x10/0x28 [ 16.961233] [<c000977c>] do_one_initcall+0xb8/0x1f8 [ 16.966714] [<c0867e04>] kernel_init_freeable+0x148/0x1e8 [ 16.972720] [<c05f9994>] kernel_init+0xc/0xe8 [ 16.977682] [<c0010038>] ret_from_fork+0x14/0x3c [ 16.982905] -> #0 (netcp_modules_lock){+.+.+.}: [ 16.987619] [<c006eab0>] lock_acquire+0x118/0x320 [ 16.992928] [<c06023f0>] mutex_lock_nested+0x68/0x4a8 [ 16.998582] [<c03e8110>] netcp_ndo_open+0x168/0x518 [ 17.004064] [<c04c48f0>] __dev_open+0xa8/0x10c [ 17.009112] [<c04c4b74>] __dev_change_flags+0x94/0x144 [ 17.014853] [<c04c4c3c>] dev_change_flags+0x18/0x48 [ 17.020334] [<c053a9fc>] devinet_ioctl+0x6dc/0x7e4 [ 17.025729] [<c04a59ec>] sock_ioctl+0x1d0/0x2a8 [ 17.030865] [<c0142844>] do_vfs_ioctl+0x41c/0x688 [ 17.036173] [<c0142ae4>] SyS_ioctl+0x34/0x5c [ 17.041046] [<c000ff60>] ret_fast_syscall+0x0/0x54 [ 17.046441] [ 17.046441] other info that might help us debug this: [ 17.046441] [ 17.054434] Possible unsafe locking scenario: [ 17.054434] [ 17.060343] CPU0 CPU1 [ 17.064862] ---- ---- [ 17.069381] lock(rtnl_mutex); [ 17.072522] lock(netcp_modules_lock); [ 17.078875] lock(rtnl_mutex); [ 17.084532] lock(netcp_modules_lock); [ 17.088366] [ 17.088366] *** DEADLOCK *** [ 17.088366] [ 17.094279] 1 lock held by ifconfig/1662: [ 17.098278] #0: (rtnl_mutex){+.+.+.}, at: [<c053a418>] devinet_ioctl+0xf8/0x7e4 [ 17.105774] [ 17.105774] stack backtrace: [ 17.110124] CPU: 1 PID: 1662 Comm: ifconfig Tainted: G W 4.1.6-01265-gfb1e101 #1 [ 17.118637] Hardware name: Keystone [ 17.122123] [<c00178e4>] (unwind_backtrace) from [<c0013cbc>] (show_stack+0x10/0x14) [ 17.129862] [<c0013cbc>] (show_stack) from [<c05ff450>] (dump_stack+0x84/0xc4) [ 17.137079] [<c05ff450>] (dump_stack) from [<c0068e34>] (print_circular_bug+0x210/0x330) [ 17.145161] [<c0068e34>] (print_circular_bug) from [<c006ab7c>] (validate_chain.isra.35+0xf98/0x13ac) [ 17.154372] [<c006ab7c>] (validate_chain.isra.35) from [<c006da60>] (__lock_acquire+0x52c/0xcc0) [ 17.163149] [<c006da60>] (__lock_acquire) from [<c006eab0>] (lock_acquire+0x118/0x320) [ 17.171058] [<c006eab0>] (lock_acquire) from [<c06023f0>] (mutex_lock_nested+0x68/0x4a8) [ 17.179140] [<c06023f0>] (mutex_lock_nested) from [<c03e8110>] (netcp_ndo_open+0x168/0x518) [ 17.187484] [<c03e8110>] (netcp_ndo_open) from [<c04c48f0>] (__dev_open+0xa8/0x10c) [ 17.195133] [<c04c48f0>] (__dev_open) from [<c04c4b74>] (__dev_change_flags+0x94/0x144) [ 17.203129] [<c04c4b74>] (__dev_change_flags) from [<c04c4c3c>] (dev_change_flags+0x18/0x48) [ 17.211560] [<c04c4c3c>] (dev_change_flags) from [<c053a9fc>] (devinet_ioctl+0x6dc/0x7e4) [ 17.219729] [<c053a9fc>] (devinet_ioctl) from [<c04a59ec>] (sock_ioctl+0x1d0/0x2a8) [ 17.227378] [<c04a59ec>] (sock_ioctl) from [<c0142844>] (do_vfs_ioctl+0x41c/0x688) [ 17.234939] [<c0142844>] (do_vfs_ioctl) from [<c0142ae4>] (SyS_ioctl+0x34/0x5c) [ 17.242242] [<c0142ae4>] (SyS_ioctl) from [<c000ff60>] (ret_fast_syscall+0x0/0x54) [ 17.258855] netcp-1.0 2620110.netcp eth0: Link is Up - 1Gbps/Full - flow control off [ 17.271282] BUG: sleeping function called from invalid context at kernel/locking/mutex.c:616 [ 17.279712] in_atomic(): 1, irqs_disabled(): 0, pid: 1662, name: ifconfig [ 17.286500] INFO: lockdep is turned off. [ 17.290413] Preemption disabled at:[< (null)>] (null) [ 17.295728] [ 17.297214] CPU: 1 PID: 1662 Comm: ifconfig Tainted: G W 4.1.6-01265-gfb1e101 #1 [ 17.305735] Hardware name: Keystone [ 17.309223] [<c00178e4>] (unwind_backtrace) from [<c0013cbc>] (show_stack+0x10/0x14) [ 17.316970] [<c0013cbc>] (show_stack) from [<c05ff450>] (dump_stack+0x84/0xc4) [ 17.324194] [<c05ff450>] (dump_stack) from [<c06023b0>] (mutex_lock_nested+0x28/0x4a8) [ 17.332112] [<c06023b0>] (mutex_lock_nested) from [<c03e9840>] (netcp_set_rx_mode+0x160/0x210) [ 17.340724] [<c03e9840>] (netcp_set_rx_mode) from [<c04c483c>] (dev_set_rx_mode+0x1c/0x28) [ 17.348982] [<c04c483c>] (dev_set_rx_mode) from [<c04c490c>] (__dev_open+0xc4/0x10c) [ 17.356724] [<c04c490c>] (__dev_open) from [<c04c4b74>] (__dev_change_flags+0x94/0x144) [ 17.364729] [<c04c4b74>] (__dev_change_flags) from [<c04c4c3c>] (dev_change_flags+0x18/0x48) [ 17.373166] [<c04c4c3c>] (dev_change_flags) from [<c053a9fc>] (devinet_ioctl+0x6dc/0x7e4) [ 17.381344] [<c053a9fc>] (devinet_ioctl) from [<c04a59ec>] (sock_ioctl+0x1d0/0x2a8) [ 17.388994] [<c04a59ec>] (sock_ioctl) from [<c0142844>] (do_vfs_ioctl+0x41c/0x688) [ 17.396563] [<c0142844>] (do_vfs_ioctl) from [<c0142ae4>] (SyS_ioctl+0x34/0x5c) [ 17.403873] [<c0142ae4>] (SyS_ioctl) from [<c000ff60>] (ret_fast_syscall+0x0/0x54) [ 17.413772] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready udhcpc (v1.20.2) started Sending discover... [ 18.690666] netcp-1.0 2620110.netcp eth0: Link is Up - 1Gbps/Full - flow control off Sending discover... [ 22.250972] netcp-1.0 2620110.netcp eth0: Link is Up - 1Gbps/Full - flow control off [ 22.258721] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 22.265458] BUG: sleeping function called from invalid context at kernel/locking/mutex.c:616 [ 22.273896] in_atomic(): 1, irqs_disabled(): 0, pid: 342, name: kworker/1:1 [ 22.280854] INFO: lockdep is turned off. [ 22.284767] Preemption disabled at:[< (null)>] (null) [ 22.290074] [ 22.291568] CPU: 1 PID: 342 Comm: kworker/1:1 Tainted: G W 4.1.6-01265-gfb1e101 #1 [ 22.300255] Hardware name: Keystone [ 22.303750] Workqueue: ipv6_addrconf addrconf_dad_work [ 22.308895] [<c00178e4>] (unwind_backtrace) from [<c0013cbc>] (show_stack+0x10/0x14) [ 22.316643] [<c0013cbc>] (show_stack) from [<c05ff450>] (dump_stack+0x84/0xc4) [ 22.323867] [<c05ff450>] (dump_stack) from [<c06023b0>] (mutex_lock_nested+0x28/0x4a8) [ 22.331786] [<c06023b0>] (mutex_lock_nested) from [<c03e9840>] (netcp_set_rx_mode+0x160/0x210) [ 22.340394] [<c03e9840>] (netcp_set_rx_mode) from [<c04c9d18>] (__dev_mc_add+0x54/0x68) [ 22.348401] [<c04c9d18>] (__dev_mc_add) from [<c05ab358>] (igmp6_group_added+0x168/0x1b4) [ 22.356580] [<c05ab358>] (igmp6_group_added) from [<c05ad2cc>] (ipv6_dev_mc_inc+0x4f0/0x5a8) [ 22.365019] [<c05ad2cc>] (ipv6_dev_mc_inc) from [<c058f0d0>] (addrconf_dad_work+0x21c/0x33c) [ 22.373460] [<c058f0d0>] (addrconf_dad_work) from [<c0042850>] (process_one_work+0x214/0x8d0) [ 22.381986] [<c0042850>] (process_one_work) from [<c0042f54>] (worker_thread+0x48/0x4bc) [ 22.390071] [<c0042f54>] (worker_thread) from [<c004868c>] (kthread+0xf0/0x108) [ 22.397381] [<c004868c>] (kthread) from [<c0010038>] Trace related to incorrect usage of mutex inside ndo_set_rx_mode [ 24.086066] BUG: sleeping function called from invalid context at kernel/locking/mutex.c:616 [ 24.094506] in_atomic(): 1, irqs_disabled(): 0, pid: 1682, name: ifconfig [ 24.101291] INFO: lockdep is turned off. [ 24.105203] Preemption disabled at:[< (null)>] (null) [ 24.110511] [ 24.112005] CPU: 2 PID: 1682 Comm: ifconfig Tainted: G W 4.1.6-01265-gfb1e101 #1 [ 24.120518] Hardware name: Keystone [ 24.124018] [<c00178e4>] (unwind_backtrace) from [<c0013cbc>] (show_stack+0x10/0x14) [ 24.131772] [<c0013cbc>] (show_stack) from [<c05ff450>] (dump_stack+0x84/0xc4) [ 24.138989] [<c05ff450>] (dump_stack) from [<c06023b0>] (mutex_lock_nested+0x28/0x4a8) [ 24.146908] [<c06023b0>] (mutex_lock_nested) from [<c03e9840>] (netcp_set_rx_mode+0x160/0x210) [ 24.155523] [<c03e9840>] (netcp_set_rx_mode) from [<c04c483c>] (dev_set_rx_mode+0x1c/0x28) [ 24.163787] [<c04c483c>] (dev_set_rx_mode) from [<c04c490c>] (__dev_open+0xc4/0x10c) [ 24.171531] [<c04c490c>] (__dev_open) from [<c04c4b74>] (__dev_change_flags+0x94/0x144) [ 24.179528] [<c04c4b74>] (__dev_change_flags) from [<c04c4c3c>] (dev_change_flags+0x18/0x48) [ 24.187966] [<c04c4c3c>] (dev_change_flags) from [<c053a9fc>] (devinet_ioctl+0x6dc/0x7e4) [ 24.196145] [<c053a9fc>] (devinet_ioctl) from [<c04a59ec>] (sock_ioctl+0x1d0/0x2a8) [ 24.203803] [<c04a59ec>] (sock_ioctl) from [<c0142844>] (do_vfs_ioctl+0x41c/0x688) [ 24.211373] [<c0142844>] (do_vfs_ioctl) from [<c0142ae4>] (SyS_ioctl+0x34/0x5c) [ 24.218676] [<c0142ae4>] (SyS_ioctl) from [<c000ff60>] (ret_fast_syscall+0x0/0x54) [ 24.227156] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready Signed-off-by: Murali Karicheri <m-karicheri2@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>

Jonathan Liu reports that the recent addition of CPU_SW_DOMAIN_PAN causes wpa_supplicant to die due to the following kernel oops: Unhandled fault: page domain fault (0x81b) at 0x001017a2 pgd = ee1b8000 [001017a2] *pgd=6ebee831, *pte=6c35475f, *ppte=6c354c7f Internal error: : 81b [#1] SMP ARM Modules linked in: rt2800usb rt2x00usb rt2800librt2x00lib crc_ccitt mac80211 CPU: 1 PID: 202 Comm: wpa_supplicant Not tainted 4.3.0-rc2 #1 Hardware name: Allwinner sun7i (A20) Family task: ec872f80 ti: ee364000 task.ti: ee364000 PC is at do_alignment_ldmstm+0x1d4/0x238 LR is at 0x0 pc : [<c001d1d8>] lr : [<00000000>] psr: 600c0113 sp : ee365e18 ip : 00000000 fp : 00000002 r10: 001017a2 r9 : 00000002 r8 : 001017aa r7 : ee365fb0 r6 : e8820018 r5 : 001017a2 r4 : 00000003 r3 : d49e30e0 r2 : 00000000 r1 : ee365fbc r0 : 00000000 Flags: nZCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment none[ 34.393106] Control: 10c5387d Table: 6e1b806a DAC: 00000051 Process wpa_supplicant (pid: 202, stack limit = 0xee364210) Stack: (0xee365e18 to 0xee366000) ... [<c001d1d8>] (do_alignment_ldmstm) from [<c001d510>] (do_alignment+0x1f0/0x904) [<c001d510>] (do_alignment) from [<c00092a0>] (do_DataAbort+0x38/0xb4) [<c00092a0>] (do_DataAbort) from [<c0013d7c>] (__dabt_usr+0x3c/0x40) Exception stack(0xee365fb0 to 0xee365ff8) 5fa0: 00000000 56c728c0 001017a2 d49e30e0 5fc0: 775448d2 597d4e74 00200800 7a9e1625 00802001 00000021 b6deec84 00000100 5fe0: 08020200 be9f4f20 0c0b0d0a b6d9b3e0 600c0010 ffffffff Code: e1a0a005 e1a0000c 1affffe8 e5913000 (e4ea3001) ---[ end trace 0acd3882fcfdf9dd ]--- This is caused by the alignment handler not being fixed up for the uaccess changes, and userspace issuing an unaligned LDM instruction. So, fix the problem by adding the necessary fixups. Reported-by: Jonathan Liu <net147@gmail.com> Tested-by: Jonathan Liu <net147@gmail.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

kvm_set_cr0 may want to call kvm_zap_gfn_range and thus access the memslots array (SRCU protected). Using a mini SRCU critical section is ugly, and adding it to kvm_arch_vcpu_create doesn't work because the VMX vcpu_create callback calls synchronize_srcu. Fixes this lockdep splat: =============================== [ INFO: suspicious RCU usage. ] 4.3.0-rc1+ #1 Not tainted ------------------------------- include/linux/kvm_host.h:488 suspicious rcu_dereference_check() usage! other info that might help us debug this: rcu_scheduler_active = 1, debug_locks = 0 1 lock held by qemu-system-i38/17000: #0: (&(&kvm->mmu_lock)->rlock){+.+...}, at: kvm_zap_gfn_range+0x24/0x1a0 [kvm] [...] Call Trace: dump_stack+0x4e/0x84 lockdep_rcu_suspicious+0xfd/0x130 kvm_zap_gfn_range+0x188/0x1a0 [kvm] kvm_set_cr0+0xde/0x1e0 [kvm] init_vmcb+0x760/0xad0 [kvm_amd] svm_create_vcpu+0x197/0x250 [kvm_amd] kvm_arch_vcpu_create+0x47/0x70 [kvm] kvm_vm_ioctl+0x302/0x7e0 [kvm] ? __lock_is_held+0x51/0x70 ? __fget+0x101/0x210 do_vfs_ioctl+0x2f4/0x560 ? __fget_light+0x29/0x90 SyS_ioctl+0x4c/0x90 entry_SYSCALL_64_fastpath+0x16/0x73 Reported-by: Borislav Petkov <bp@alien8.de> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>

ppp_dev_uninit() locks all_ppp_mutex while under rtnl mutex protection. ppp_create_interface() must then lock these mutexes in that same order to avoid possible deadlock. [ 120.880011] ====================================================== [ 120.880011] [ INFO: possible circular locking dependency detected ] [ 120.880011] 4.2.0 #1 Not tainted [ 120.880011] ------------------------------------------------------- [ 120.880011] ppp-apitest/15827 is trying to acquire lock: [ 120.880011] (&pn->all_ppp_mutex){+.+.+.}, at: [<ffffffffa0145f56>] ppp_dev_uninit+0x64/0xb0 [ppp_generic] [ 120.880011] [ 120.880011] but task is already holding lock: [ 120.880011] (rtnl_mutex){+.+.+.}, at: [<ffffffff812e4255>] rtnl_lock+0x12/0x14 [ 120.880011] [ 120.880011] which lock already depends on the new lock. [ 120.880011] [ 120.880011] [ 120.880011] the existing dependency chain (in reverse order) is: [ 120.880011] [ 120.880011] -> #1 (rtnl_mutex){+.+.+.}: [ 120.880011] [<ffffffff81073a6f>] lock_acquire+0xcf/0x10e [ 120.880011] [<ffffffff813ab18a>] mutex_lock_nested+0x56/0x341 [ 120.880011] [<ffffffff812e4255>] rtnl_lock+0x12/0x14 [ 120.880011] [<ffffffff812d9d94>] register_netdev+0x11/0x27 [ 120.880011] [<ffffffffa0147b17>] ppp_ioctl+0x289/0xc98 [ppp_generic] [ 120.880011] [<ffffffff8113b367>] do_vfs_ioctl+0x4ea/0x532 [ 120.880011] [<ffffffff8113b3fd>] SyS_ioctl+0x4e/0x7d [ 120.880011] [<ffffffff813ad7d7>] entry_SYSCALL_64_fastpath+0x12/0x6f [ 120.880011] [ 120.880011] -> #0 (&pn->all_ppp_mutex){+.+.+.}: [ 120.880011] [<ffffffff8107334e>] __lock_acquire+0xb07/0xe76 [ 120.880011] [<ffffffff81073a6f>] lock_acquire+0xcf/0x10e [ 120.880011] [<ffffffff813ab18a>] mutex_lock_nested+0x56/0x341 [ 120.880011] [<ffffffffa0145f56>] ppp_dev_uninit+0x64/0xb0 [ppp_generic] [ 120.880011] [<ffffffff812d5263>] rollback_registered_many+0x19e/0x252 [ 120.880011] [<ffffffff812d5381>] rollback_registered+0x29/0x38 [ 120.880011] [<ffffffff812d53fa>] unregister_netdevice_queue+0x6a/0x77 [ 120.880011] [<ffffffffa0146a94>] ppp_release+0x42/0x79 [ppp_generic] [ 120.880011] [<ffffffff8112d9f6>] __fput+0xec/0x192 [ 120.880011] [<ffffffff8112dacc>] ____fput+0x9/0xb [ 120.880011] [<ffffffff8105447a>] task_work_run+0x66/0x80 [ 120.880011] [<ffffffff81001801>] prepare_exit_to_usermode+0x8c/0xa7 [ 120.880011] [<ffffffff81001900>] syscall_return_slowpath+0xe4/0x104 [ 120.880011] [<ffffffff813ad931>] int_ret_from_sys_call+0x25/0x9f [ 120.880011] [ 120.880011] other info that might help us debug this: [ 120.880011] [ 120.880011] Possible unsafe locking scenario: [ 120.880011] [ 120.880011] CPU0 CPU1 [ 120.880011] ---- ---- [ 120.880011] lock(rtnl_mutex); [ 120.880011] lock(&pn->all_ppp_mutex); [ 120.880011] lock(rtnl_mutex); [ 120.880011] lock(&pn->all_ppp_mutex); [ 120.880011] [ 120.880011] *** DEADLOCK *** Fixes: 8cb775b ("ppp: fix device unregistration upon netns deletion") Reported-by: Sedat Dilek <sedat.dilek@gmail.com> Tested-by: Sedat Dilek <sedat.dilek@gmail.com> Signed-off-by: Guillaume Nault <g.nault@alphalink.fr> Signed-off-by: David S. Miller <davem@davemloft.net>

Andrey reported a panic: [ 7249.865507] BUG: unable to handle kernel pointer dereference at 000000b4 [ 7249.865559] IP: [<c16afeca>] icmp_route_lookup+0xaa/0x320 [ 7249.865598] *pdpt = 0000000030f7f001 *pde = 0000000000000000 [ 7249.865637] Oops: 0000 [#1] ... [ 7249.866811] CPU: 0 PID: 0 Comm: swapper/0 Not tainted 4.3.0-999-generic #201509220155 [ 7249.866876] Hardware name: MSI MS-7250/MS-7250, BIOS 080014 08/02/2006 [ 7249.866916] task: c1a5ab00 ti: c1a52000 task.ti: c1a52000 [ 7249.866949] EIP: 0060:[<c16afeca>] EFLAGS: 00210246 CPU: 0 [ 7249.866981] EIP is at icmp_route_lookup+0xaa/0x320 [ 7249.867012] EAX: 00000000 EBX: f483ba48 ECX: 00000000 EDX: f2e18a00 [ 7249.867045] ESI: 000000c0 EDI: f483ba70 EBP: f483b9ec ESP: f483b974 [ 7249.867077] DS: 007b ES: 007b FS: 00d8 GS: 00e0 SS: 0068 [ 7249.867108] CR0: 8005003b CR2: 000000b4 CR3: 36ee07c0 CR4: 000006f0 [ 7249.867141] Stack: [ 7249.867165] 320310ee 00000000 00000042 320310ee 00000000 c1aeca00 f3920240 f0c69180 [ 7249.867268] f483ba04 f855058b a89b66cd f483ba44 f8962f4b 00000000 e659266c f483ba54 [ 7249.867361] 8004753c f483ba5c f8962f4b f2031140 000003c1 ffbd8fa0 c16b0e00 00000064 [ 7249.867448] Call Trace: [ 7249.867494] [<f855058b>] ? e1000_xmit_frame+0x87b/0xdc0 [e1000e] [ 7249.867534] [<f8962f4b>] ? tcp_in_window+0xeb/0xb10 [nf_conntrack] [ 7249.867576] [<f8962f4b>] ? tcp_in_window+0xeb/0xb10 [nf_conntrack] [ 7249.867615] [<c16b0e00>] ? icmp_send+0xa0/0x380 [ 7249.867648] [<c16b102f>] icmp_send+0x2cf/0x380 [ 7249.867681] [<f89c8126>] nf_send_unreach+0xa6/0xc0 [nf_reject_ipv4] [ 7249.867714] [<f89cd0da>] reject_tg+0x7a/0x9f [ipt_REJECT] [ 7249.867746] [<f88c29a7>] ipt_do_table+0x317/0x70c [ip_tables] [ 7249.867780] [<f895e0a6>] ? __nf_conntrack_find_get+0x166/0x3b0 [nf_conntrack] [ 7249.867838] [<f895eea8>] ? nf_conntrack_in+0x398/0x600 [nf_conntrack] [ 7249.867889] [<f84c0035>] iptable_filter_hook+0x35/0x80 [iptable_filter] [ 7249.867933] [<c16776a1>] nf_iterate+0x71/0x80 [ 7249.867970] [<c1677715>] nf_hook_slow+0x65/0xc0 [ 7249.868002] [<c1681811>] __ip_local_out_sk+0xc1/0xd0 [ 7249.868034] [<c1680f30>] ? ip_forward_options+0x1a0/0x1a0 [ 7249.868066] [<c1681836>] ip_local_out_sk+0x16/0x30 [ 7249.868097] [<c1684054>] ip_send_skb+0x14/0x80 [ 7249.868129] [<c16840f4>] ip_push_pending_frames+0x34/0x40 [ 7249.868163] [<c16844a2>] ip_send_unicast_reply+0x282/0x310 [ 7249.868196] [<c16a0863>] tcp_v4_send_reset+0x1b3/0x380 [ 7249.868227] [<c16a1b63>] tcp_v4_rcv+0x323/0x990 [ 7249.868257] [<c16776a1>] ? nf_iterate+0x71/0x80 [ 7249.868289] [<c167dc2b>] ip_local_deliver_finish+0x8b/0x230 [ 7249.868322] [<c167df4c>] ip_local_deliver+0x4c/0xa0 [ 7249.868353] [<c167dba0>] ? ip_rcv_finish+0x390/0x390 [ 7249.868384] [<c167d88c>] ip_rcv_finish+0x7c/0x390 [ 7249.868415] [<c167e280>] ip_rcv+0x2e0/0x420 ... Prior to the VRF change the oif was not set in the flow struct, so the VRF support should really have only added the vrf_master_ifindex lookup. Fixes: 613d09b ("net: Use VRF device index for lookups on TX") Cc: Andrey Melnikov <temnota.am@gmail.com> Signed-off-by: David Ahern <dsa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>

it was broken by 35d5d20 "mtd: mxc_nand: cleanup copy_spare function" else we get the following error : [ 22.709507] ubi0: attaching mtd3 [ 23.613470] ubi0: scanning is finished [ 23.617278] ubi0: empty MTD device detected [ 23.623219] Unhandled fault: imprecise external abort (0x1c06) at 0x9e62f0ec [ 23.630291] pgd = 9df80000 [ 23.633005] [9e62f0ec] *pgd=8e60041e(bad) [ 23.637064] Internal error: : 1c06 [#1] SMP ARM [ 23.641605] Modules linked in: [ 23.644687] CPU: 0 PID: 99 Comm: ubiattach Not tainted 4.2.0-dirty #22 [ 23.651222] Hardware name: Freescale i.MX53 (Device Tree Support) [ 23.657322] task: 9e687300 ti: 9dcfc000 task.ti: 9dcfc000 [ 23.662744] PC is at memcpy16_toio+0x4c/0x74 [ 23.667026] LR is at mxc_nand_command+0x484/0x640 [ 23.671739] pc : [<803f9c08>] lr : [<803faeb0>] psr: 60000013 [ 23.671739] sp : 9dcfdb10 ip : 9e62f0ea fp : 9dcfdb1c [ 23.683222] r10: a09c1000 r9 : 0000001a r8 : ffffffff [ 23.688453] r7 : ffffffff r6 : 9e674810 r5 : 9e674810 r4 : 000000b6 [ 23.694985] r3 : a09c16a4 r2 : a09c16a4 r1 : a09c16a4 r0 : 0000ffff [ 23.701521] Flags: nZCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment user [ 23.708662] Control: 10c5387d Table: 8df80019 DAC: 00000015 [ 23.714413] Process ubiattach (pid: 99, stack limit = 0x9dcfc210) [ 23.720514] Stack: (0x9dcfdb10 to 0x9dcfe000) [ 23.724881] db00: 9dcfdb6c 9dcfdb20 803faeb0 803f9bc8 [ 23.733069] db20: 803f227c 803f9b74 ffffffff 9e674810 9e674810 9e674810 00000040 9e62f010 [ 23.741255] db40: 803faa2c 9e674b40 9e674810 803faa2c 00000400 803faa2c 00000000 9df42800 [ 23.749441] db60: 9dcfdb9c 9dcfdb70 803f2024 803faa38 9e4201cc 00000000 803f0a78 9e674b40 [ 23.757627] db80: 803f1f80 9e674810 00000400 00000400 9dcfdc14 9dcfdba0 803f3bd8 803f1f8c [ 23.765814] dba0: 9e4201cc 00000000 00000580 00000000 00000000 800718c0 0000007f 00001000 [ 23.774000] dbc0: 9df42800 000000e0 00000000 00000000 9e4201cc 00000000 00000000 00000000 [ 23.782186] dbe0: 00000580 00000580 00000000 9e674810 9dcfdc20 9dcfdce8 9df42800 00580000 [ 23.790372] dc00: 00000000 00000400 9dcfdc6c 9dcfdc18 803f3f94 803f39a4 9dcfdc20 00000000 [ 23.798558] dc20: 00000000 00000400 00000000 00000000 00000000 00000000 9df42800 00000000 [ 23.806744] dc40: 9dcfdd0c 00580000 00000000 00000400 00000000 9df42800 9dee1000 9d802000 [ 23.814930] dc60: 9dcfdc94 9dcfdc70 803eb63c 803f3f38 00000400 9dcfdce8 9df42800 dead4ead [ 23.823116] dc80: 803eb5f4 00000000 9dcfdcc4 9dcfdc98 803e82ac 803eb600 00000400 9dcfdce8 [ 23.831301] dca0: 9df42800 00000400 9dee0000 00000000 00000400 00000000 9dcfdd1c 9dcfdcc8 [ 23.839488] dcc0: 80406048 803e8230 00000400 9dcfdce8 9df42800 9dcfdc78 00000008 00000000 [ 23.847673] dce0: 00000000 00000000 00000000 00000004 00000000 9df42800 9dee0000 00000000 [ 23.855859] dd00: 9d802030 00000000 9dc8b214 9d802000 9dcfdd44 9dcfdd20 804066cc 80405f50 [ 23.864047] dd20: 00000400 9dc8b200 9d802030 9df42800 9dee0000 9dc8b200 9dcfdd84 9dcfdd48 [ 23.872233] dd40: 8040a544 804065ac 9e401c80 000080d0 9dcfdd84 00000001 800fc828 9df42400 [ 23.880418] dd60: 00000000 00000080 9dc8b200 9dc8b200 9dc8b200 9dee0000 9dcfdddc 9dcfdd8 [ 23.888605] dd80: 803fb560 8040a440 9dcfddc4 9dcfdd98 800f1428 9dee1000 a0acf000 00000000 [ 23.896792] dda0: 00000000 ffffffff 00000006 00000000 9dee0000 9dee0000 00005600 00000080 [ 23.904979] ddc0: 9dc8b200 a0acf000 9dc8b200 8112514c 9dcfde24 9dcfdde0 803fc08c 803fb4f0 [ 23.913165] dde0: 9e401c80 00000013 9dcfde04 9dcfddf8 8006bbf8 8006ba00 9dcfde24 00000000 [ 23.921351] de00: 9dee0000 00000065 9dee0000 00000001 9dc8b200 8112514c 9dcfde84 9dcfde28 [ 23.929538] de20: 8040afa0 803fb948 ffffffff 00000000 9dc8b214 9dcfde40 800f1428 800f11dc [ 23.937724] de40: 9dc8b21 9dc8b20c 9dc8b204 9dee1000 9dc8b214 8069bb60 fffff000 fffff000 [ 23.945911] de60: 9e7b5400 00000000 9dee0000 9dee1000 00001000 9e7b5400 9dcfdecc 9dcfde88 [ 23.954097] de80: 803ff1bc 8040a630 9dcfdea4 9dcfde98 00000800 00000800 9dcfdecc 9dcfdea8 [ 23.962284] dea0: 803e8f6c 00000000 7e87ab70 9e7b5400 80113e30 00000003 9dcfc000 00000000 [ 23.970470] dec0: 9dcfdf04 9dcfded0 804008cc 803feb98 ffffffff 00000003 00000000 00000000 [ 23.978656] dee0: 00000000 00000000 9e7cb000 9dc193e0 7e87ab70 9dd92140 9dcfdf7c 9dcfdf08 [ 23.986842] df00: 80113b5c 8040080c 800fbed8 8006bbf0 9e7cb000 00000003 9e7cb000 9dd92140 [ 23.995029] df20: 9dc193e0 9dd92148 9dcfdf4c 9dcfdf38 8011022c 800fbe78 8000f9cc 9e687300 [ 24.003216] df40: 9dcfdf6c 9dcfdf50 8011f798 8007ffe8 7e87ab70 9dd92140 00000003 9dd92140 [ 24.011402] df60: 40186f40 7e87ab70 9dcfc000 00000000 9dcfdfa4 9dcfdf8 80113e30 8011373c [ 24.019588] df80: 7e87ab70 7e87ab70 7e87aea9 00000036 8000fb8 9dcfc000 00000000 9dcfdfa8 [ 24.027775] dfa0: 8000f9a0 80113e00 7e87ab70 7e87ab70 00000003 40186f40 7e87ab70 00000000 [ 24.035962] dfc0: 7e87ab70 7e87ab70 7e87aea9 00000036 00000000 00000000 76fd1f70 00000000 [ 24.044148] dfe0: 76f80f8c 7e87ab2 00009810 76f80fc4 60000010 00000003 00000000 00000000 [ 24.052328] Backtrace: [ 24.054806] [<803f9bbc>] (memcpy16_toio) from [<803faeb0>] (mxc_nand_command+0x484/0x640) [ 24.062996] [<803faa2c>] (mxc_nand_command) from [<803f2024>] (nand_write_page+0xa4/0x154) [ 24.071264] r10:9df42800 r9:00000000 r8:803faa2c r7:00000400 r6:803faa2c r5:9e674810 [ 24.079180] r4:9e674b40 [ 24.081738] [<803f1f80>] (nand_write_page) from [<803f3bd8>] (nand_do_write_ops+0x240/0x444) [ 24.090180] r8:00000400 r7:00000400 r6:9e674810 r5:803f1f80 r4:9e674b40 [ 24.096970] [<803f3998>] (nand_do_write_ops) from [<803f3f94>] (nand_write+0x68/0x88) [ 24.104804] r10:00000400 r9:00000000 r8:00580000 r7:9df42800 r6:9dcfdce8 r5:9dcfdc20 [ 24.112719] r4:9e674810 [ 24.115287] [<803f3f2c>] (nand_write) from [<803eb63c>] (part_write+0x48/0x50) [ 24.122514] r10:9d802000 r9:9dee1000 r8:9df42800 r7:00000000 r6:00000400 r5:00000000 [ 24.130429] r4:00580000 [ 24.132989] [<803eb5f4>] (part_write) from [<803e82ac>] (mtd_write+0x88/0xa0) [ 24.140129] r5:00000000 r4:803eb5f4 [ 24.143748] [<803e8224>] (mtd_write) from [<80406048>] (ubi_io_write+0x104/0x65c) [ 24.151235] r7:00000000 r6:00000400 r5:00000000 r4:9dee0000 [ 24.156968] [<80405f44>] (ubi_io_write) from [<804066cc>] (ubi_io_write_ec_hdr+0x12c/0x190) [ 24.165323] r10:9d802000 r9:9dc8b214 r8:00000000 r7:9d802030 r6:00000000 r5:9dee0000 [ 24.173239] r4:9df42800 [ 24.175798] [<804065a0>] (ubi_io_write_ec_hdr) from [<8040a544>] (ubi_early_get_peb+0x110/0x1f0) [ 24.184587] r6:9dc8b200 r5:9dee0000 r4:9df42800 [ 24.189262] [<8040a434>] (ubi_early_get_peb) from [<803fb560>] (create_vtbl+0x7c/0x238) [ 24.197271] r10:9dee0000 r9:9dc8b200 r8:9dc8b200 r7:9dc8b200 r6:00000080 r5:00000000 [ 24.205187] r4:9df42400 [ 24.207746] [<803fb4e4>] (create_vtbl) from [<803fc08c>] (ubi_read_volume_table+0x750/0xa64) [ 24.216187] r10:8112514c r9:9dc8b200 r8:a0acf000 r7:9dc8b200 r6:00000080 r5:00005600 [ 24.224103] r4:9dee0000 [ 24.226662] [<803fb93c>] (ubi_read_volume_table) from [<8040afa0>] (ubi_attach+0x97c/0x152c) [ 24.235103] r10:8112514c r9:9dc8b200 r8:00000001 r7:9dee0000 r6:00000065 r5:9dee0000 [ 24.243018] r4:00000000 [ 24.245579] [<8040a624>] (ubi_attach) from [<803ff1bc>] (ubi_attach_mtd_dev+0x630/0xbac) [ 24.253673] r10:9e7b5400 r9:00001000 r8:9dee1000 r7:9dee0000 r6:00000000 r5:9e7b5400 [ 24.261588] r4:fffff000 [ 24.264148] [<803feb8c>] (ubi_attach_mtd_dev) from [<804008cc>] (ctrl_cdev_ioctl+0xcc/0x1cc) [ 24.272589] r10:00000000 r9:9dcfc000 r8:00000003 r7:80113e30 r6:9e7b5400 r5:7e87ab70 [ 24.280505] r4:00000000 [ 24.283070] [<80400800>] (ctrl_cdev_ioctl) from [<80113b5c>] (do_vfs_ioctl+0x42c/0x6c4) [ 24.291077] r6:9dd92140 r5:7e87ab70 r4:9dc193e0 [ 24.295753] [<80113730>] (do_vfs_ioctl) from [<80113e30>] (SyS_ioctl+0x3c/0x64) [ 24.303066] r10:00000000 r9:9dcfc000 r8:7e87ab70 r7:40186f40 r6:9dd92140 r5:00000003 [ 24.310981] r4:9dd92140 [ 24.313549] [<80113df4>] (SyS_ioctl) from [<8000f9a0>] (ret_fast_syscall+0x0/0x54) [ 24.321123] r9:9dcfc000 r8:8000fb84 r7:00000036 r6:7e87aea9 r5:7e87ab70 r4:7e87ab70 [ 24.328957] Code: e1c300b0 e1510002 e1a03001 1afffff9 (e89da800) [ 24.335066] ---[ end trace ab1cb17887f21bbb ]--- [ 24.340249] Unhandled fault: imprecise external abort (0x1c06) at 0x7ee8bcf0 [ 24.347310] pgd = 9df3c000 [ 24.350023] [7ee8bcf0] *pgd=8dcbf831, *pte=8eb3334f, *ppte=8eb3383f Segmentation fault Fixes: 35d5d20 ("mtd: mxc_nand: cleanup copy_spare function") Signed-off-by: Eric Bénard <eric@eukrea.com> Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Reviewed-by: Baruch Siach <baruch@tkos.co.il> Cc: <stable@vger.kernel.org> Signed-off-by: Brian Norris <computersforpeace@gmail.com>

…t initialized. In case something goes wrong with power well initialization we were calling intel_prepare_ddi during boot while encoder list isnt't initilized. [ 9.618747] i915 0000:00:02.0: Invalid ROM contents [ 9.631446] [drm] failed to find VBIOS tables [ 9.720036] BUG: unable to handle kernel NULL pointer dereference at 00000000 00000058 [ 9.721986] IP: [<ffffffffa014eb72>] ddi_get_encoder_port+0x82/0x190 [i915] [ 9.723736] PGD 0 [ 9.724286] Oops: 0000 [#1] PREEMPT SMP [ 9.725386] Modules linked in: intel_powerclamp snd_hda_intel(+) coretemp crc 32c_intel snd_hda_codec snd_hda_core serio_raw snd_pcm snd_timer i915(+) parport _pc parport pinctrl_sunrisepoint pinctrl_intel nfsd nfs_acl [ 9.730635] CPU: 0 PID: 497 Comm: systemd-udevd Not tainted 4.3.0-rc2-eywa-10 967-g72de2cfd-dirty #2 [ 9.732785] Hardware name: Intel Corporation Cannonlake Client platform/Skyla ke DT DDR4 RVP8, BIOS CNLSE2R1.R00.X021.B00.1508040310 08/04/2015 [ 9.735785] task: ffff88008a704700 ti: ffff88016a1ac000 task.ti: ffff88016a1a c000 [ 9.737584] RIP: 0010:[<ffffffffa014eb72>] [<ffffffffa014eb72>] ddi_get_enco der_port+0x82/0x190 [i915] [ 9.739934] RSP: 0000:ffff88016a1af710 EFLAGS: 00010296 [ 9.741184] RAX: 000000000000004e RBX: ffff88008a9edc98 RCX: 0000000000000001 [ 9.742934] RDX: 000000000000004e RSI: ffffffff81fc1e82 RDI: 00000000ffffffff [ 9.744634] RBP: ffff88016a1af730 R08: 0000000000000000 R09: 0000000000000578 [ 9.746333] R10: 0000000000001065 R11: 0000000000000578 R12: fffffffffffffff8 [ 9.748033] R13: ffff88016a1af7a8 R14: ffff88016a1af794 R15: 0000000000000000 [ 9.749733] FS: 00007eff2e1e07c0(0000) GS:ffff88016fc00000(0000) knlGS:00000 00000000000 [ 9.751683] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 9.753083] CR2: 0000000000000058 CR3: 000000016922b000 CR4: 00000000003406f0 [ 9.754782] Stack: [ 9.755332] ffff88008a9edc98 ffff88008a9ed800 ffffffffa01d07b0 00000000fffb9 09e [ 9.757232] ffff88016a1af7d8 ffffffffa0154ea7 0000000000000246 ffff88016a370 080 [ 9.759182] ffff88016a370080 ffff88008a9ed800 0000000000000246 ffff88008a9ed c98 [ 9.761132] Call Trace: [ 9.761782] [<ffffffffa0154ea7>] intel_prepare_ddi+0x67/0x860 [i915] [ 9.763332] [<ffffffff81a56996>] ? _raw_spin_unlock_irqrestore+0x26/0x40 [ 9.765031] [<ffffffffa00fad01>] ? gen9_read32+0x141/0x360 [i915] [ 9.766531] [<ffffffffa00b43e1>] skl_set_power_well+0x431/0xa80 [i915] [ 9.768181] [<ffffffffa00b4a63>] skl_power_well_enable+0x13/0x20 [i915] [ 9.769781] [<ffffffffa00b2188>] intel_power_well_enable+0x28/0x50 [i915] [ 9.771481] [<ffffffffa00b4d52>] intel_display_power_get+0x92/0xc0 [i915] [ 9.773180] [<ffffffffa00b4fcb>] intel_display_set_init_power+0x3b/0x40 [i91 5] [ 9.774980] [<ffffffffa00b5170>] intel_power_domains_init_hw+0x120/0x520 [i9 15] [ 9.776780] [<ffffffffa0194c61>] i915_driver_load+0xb21/0xf40 [i915] So let's protect this case. My first attempt was to remove the intel_prepare_ddi, but Daniel had pointed out this is really needed to restore those registers values. And Imre pointed out that this case was without the flag protection and this was actually where things were going bad. So I've just checked and this indeed solves my issue. The regressing intel_prepare_ddi call was added in commit 1d2b952 Author: Damien Lespiau <damien.lespiau@intel.com> Date: Fri Mar 6 18:50:53 2015 +0000 drm/i915/skl: Restore the DDI translation tables when enabling PW1 Cc: Imre Deak <imre.deak@intel.com> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> [Jani: regression reference] Signed-off-by: Jani Nikula <jani.nikula@intel.com>

…ut event A case can occur when sctp_accept() is called by the user during a heartbeat timeout event after the 4-way handshake. Since sctp_assoc_migrate() changes both assoc->base.sk and assoc->ep, the bh_sock_lock in sctp_generate_heartbeat_event() will be taken with the listening socket but released with the new association socket. The result is a deadlock on any future attempts to take the listening socket lock. Note that this race can occur with other SCTP timeouts that take the bh_lock_sock() in the event sctp_accept() is called. BUG: soft lockup - CPU#9 stuck for 67s! [swapper:0] ... RIP: 0010:[<ffffffff8152d48e>] [<ffffffff8152d48e>] _spin_lock+0x1e/0x30 RSP: 0018:ffff880028323b20 EFLAGS: 00000206 RAX: 0000000000000002 RBX: ffff880028323b20 RCX: 0000000000000000 RDX: 0000000000000000 RSI: ffff880028323be0 RDI: ffff8804632c4b48 RBP: ffffffff8100bb93 R08: 0000000000000000 R09: 0000000000000000 R10: ffff880610662280 R11: 0000000000000100 R12: ffff880028323aa0 R13: ffff8804383c3880 R14: ffff880028323a90 R15: ffffffff81534225 FS: 0000000000000000(0000) GS:ffff880028320000(0000) knlGS:0000000000000000 CS: 0010 DS: 0018 ES: 0018 CR0: 000000008005003b CR2: 00000000006df528 CR3: 0000000001a85000 CR4: 00000000000006e0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400 Process swapper (pid: 0, threadinfo ffff880616b70000, task ffff880616b6cab0) Stack: ffff880028323c40 ffffffffa01c2582 ffff880614cfb020 0000000000000000 <d> 0100000000000000 00000014383a6c44 ffff8804383c3880 ffff880614e93c00 <d> ffff880614e93c00 0000000000000000 ffff8804632c4b00 ffff8804383c38b8 Call Trace: <IRQ> [<ffffffffa01c2582>] ? sctp_rcv+0x492/0xa10 [sctp] [<ffffffff8148c559>] ? nf_iterate+0x69/0xb0 [<ffffffff814974a0>] ? ip_local_deliver_finish+0x0/0x2d0 [<ffffffff8148c716>] ? nf_hook_slow+0x76/0x120 [<ffffffff814974a0>] ? ip_local_deliver_finish+0x0/0x2d0 [<ffffffff8149757d>] ? ip_local_deliver_finish+0xdd/0x2d0 [<ffffffff81497808>] ? ip_local_deliver+0x98/0xa0 [<ffffffff81496ccd>] ? ip_rcv_finish+0x12d/0x440 [<ffffffff81497255>] ? ip_rcv+0x275/0x350 [<ffffffff8145cfeb>] ? __netif_receive_skb+0x4ab/0x750 ... With lockdep debugging: ===================================== [ BUG: bad unlock balance detected! ] ------------------------------------- CslRx/12087 is trying to release lock (slock-AF_INET) at: [<ffffffffa01bcae0>] sctp_generate_timeout_event+0x40/0xe0 [sctp] but there are no more locks to release! other info that might help us debug this: 2 locks held by CslRx/12087: #0: (&asoc->timers[i]){+.-...}, at: [<ffffffff8108ce1f>] run_timer_softirq+0x16f/0x3e0 #1: (slock-AF_INET){+.-...}, at: [<ffffffffa01bcac3>] sctp_generate_timeout_event+0x23/0xe0 [sctp] Ensure the socket taken is also the same one that is released by saving a copy of the socket before entering the timeout event critical section. Signed-off-by: Karl Heiss <kheiss@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>

Fixes the following lockdep splat: [ 1.244527] ============================================= [ 1.245193] [ INFO: possible recursive locking detected ] [ 1.245193] 4.2.0-rc1+ #37 Not tainted [ 1.245193] --------------------------------------------- [ 1.245193] cp/742 is trying to acquire lock: [ 1.245193] (&sb->s_type->i_mutex_key#9){+.+.+.}, at: [<ffffffff812b3f69>] ubifs_init_security+0x29/0xb0 [ 1.245193] [ 1.245193] but task is already holding lock: [ 1.245193] (&sb->s_type->i_mutex_key#9){+.+.+.}, at: [<ffffffff81198e7f>] path_openat+0x3af/0x1280 [ 1.245193] [ 1.245193] other info that might help us debug this: [ 1.245193] Possible unsafe locking scenario: [ 1.245193] [ 1.245193] CPU0 [ 1.245193] ---- [ 1.245193] lock(&sb->s_type->i_mutex_key#9); [ 1.245193] lock(&sb->s_type->i_mutex_key#9); [ 1.245193] [ 1.245193] *** DEADLOCK *** [ 1.245193] [ 1.245193] May be due to missing lock nesting notation [ 1.245193] [ 1.245193] 2 locks held by cp/742: [ 1.245193] #0: (sb_writers#5){.+.+.+}, at: [<ffffffff811ad37f>] mnt_want_write+0x1f/0x50 [ 1.245193] #1: (&sb->s_type->i_mutex_key#9){+.+.+.}, at: [<ffffffff81198e7f>] path_openat+0x3af/0x1280 [ 1.245193] [ 1.245193] stack backtrace: [ 1.245193] CPU: 2 PID: 742 Comm: cp Not tainted 4.2.0-rc1+ #37 [ 1.245193] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.7.5-0-ge51488c-20140816_022509-build35 04/01/2014 [ 1.245193] ffffffff8252d530 ffff88007b023a38 ffffffff814f6f49 ffffffff810b56c5 [ 1.245193] ffff88007c30cc80 ffff88007b023af8 ffffffff810a150d ffff88007b023a68 [ 1.245193] 000000008101302a ffff880000000000 00000008f447e23f ffffffff8252d500 [ 1.245193] Call Trace: [ 1.245193] [<ffffffff814f6f49>] dump_stack+0x4c/0x65 [ 1.245193] [<ffffffff810b56c5>] ? console_unlock+0x1c5/0x510 [ 1.245193] [<ffffffff810a150d>] __lock_acquire+0x1a6d/0x1ea0 [ 1.245193] [<ffffffff8109fa78>] ? __lock_is_held+0x58/0x80 [ 1.245193] [<ffffffff810a1a93>] lock_acquire+0xd3/0x270 [ 1.245193] [<ffffffff812b3f69>] ? ubifs_init_security+0x29/0xb0 [ 1.245193] [<ffffffff814fc83b>] mutex_lock_nested+0x6b/0x3a0 [ 1.245193] [<ffffffff812b3f69>] ? ubifs_init_security+0x29/0xb0 [ 1.245193] [<ffffffff812b3f69>] ? ubifs_init_security+0x29/0xb0 [ 1.245193] [<ffffffff812b3f69>] ubifs_init_security+0x29/0xb0 [ 1.245193] [<ffffffff8128e286>] ubifs_create+0xa6/0x1f0 [ 1.245193] [<ffffffff81198e7f>] ? path_openat+0x3af/0x1280 [ 1.245193] [<ffffffff81195d15>] vfs_create+0x95/0xc0 [ 1.245193] [<ffffffff8119929c>] path_openat+0x7cc/0x1280 [ 1.245193] [<ffffffff8109ffe3>] ? __lock_acquire+0x543/0x1ea0 [ 1.245193] [<ffffffff81088f20>] ? sched_clock_cpu+0x90/0xc0 [ 1.245193] [<ffffffff81088c00>] ? calc_global_load_tick+0x60/0x90 [ 1.245193] [<ffffffff81088f20>] ? sched_clock_cpu+0x90/0xc0 [ 1.245193] [<ffffffff811a9cef>] ? __alloc_fd+0xaf/0x180 [ 1.245193] [<ffffffff8119ac55>] do_filp_open+0x75/0xd0 [ 1.245193] [<ffffffff814ffd86>] ? _raw_spin_unlock+0x26/0x40 [ 1.245193] [<ffffffff811a9cef>] ? __alloc_fd+0xaf/0x180 [ 1.245193] [<ffffffff81189bd9>] do_sys_open+0x129/0x200 [ 1.245193] [<ffffffff81189cc9>] SyS_open+0x19/0x20 [ 1.245193] [<ffffffff81500717>] entry_SYSCALL_64_fastpath+0x12/0x6f While the lockdep splat is a false positive, becuase path_openat holds i_mutex of the parent directory and ubifs_init_security() tries to acquire i_mutex of a new inode, it reveals that taking i_mutex in ubifs_init_security() is in vain because it is only being called in the inode allocation path and therefore nobody else can see the inode yet. Cc: stable@vger.kernel.org # 3.20- Reported-and-tested-by: Boris Brezillon <boris.brezillon@free-electrons.com> Reviewed-and-tested-by: Dongsheng Yang <yangds.fnst@cn.fujitsu.com> Signed-off-by: Richard Weinberger <richard@nod.at> Signed-off-by: dedekind1@gmail.com

My system keeps crashing with below message. vmstat_update() schedules a delayed work in current cpu and expects the work runs in the cpu. schedule_delayed_work() is expected to make delayed work run in local cpu. The problem is timer can be migrated with NO_HZ. __queue_work() queues work in timer handler, which could run in a different cpu other than where the delayed work is scheduled. The end result is the delayed work runs in different cpu. The patch makes __queue_delayed_work records local cpu earlier. Where the timer runs doesn't change where the work runs with the change. [ 28.010131] ------------[ cut here ]------------ [ 28.010609] kernel BUG at ../mm/vmstat.c:1392! [ 28.011099] invalid opcode: 0000 [#1] PREEMPT SMP DEBUG_PAGEALLOC KASAN [ 28.011860] Modules linked in: [ 28.012245] CPU: 0 PID: 289 Comm: kworker/0:3 Tainted: G W4.3.0-rc3+ torvalds#634 [ 28.013065] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.7.5-20140709_153802- 04/01/2014 [ 28.014160] Workqueue: events vmstat_update [ 28.014571] task: ffff880117682580 ti: ffff8800ba428000 task.ti: ffff8800ba428000 [ 28.015445] RIP: 0010:[<ffffffff8115f921>] [<ffffffff8115f921>]vmstat_update+0x31/0x80 [ 28.016282] RSP: 0018:ffff8800ba42fd80 EFLAGS: 00010297 [ 28.016812] RAX: 0000000000000000 RBX: ffff88011a858dc0 RCX:0000000000000000 [ 28.017585] RDX: ffff880117682580 RSI: ffffffff81f14d8c RDI:ffffffff81f4df8d [ 28.018366] RBP: ffff8800ba42fd90 R08: 0000000000000001 R09:0000000000000000 [ 28.019169] R10: 0000000000000000 R11: 0000000000000121 R12:ffff8800baa9f640 [ 28.019947] R13: ffff88011a81e340 R14: ffff88011a823700 R15:0000000000000000 [ 28.020071] FS: 0000000000000000(0000) GS:ffff88011a800000(0000)knlGS:0000000000000000 [ 28.020071] CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b [ 28.020071] CR2: 00007ff6144b01d0 CR3: 00000000b8e93000 CR4:00000000000006f0 [ 28.020071] Stack: [ 28.020071] ffff88011a858dc0 ffff8800baa9f640 ffff8800ba42fe00ffffffff8106bd88 [ 28.020071] ffffffff8106bd0b 0000000000000096 0000000000000000ffffffff82f9b1e8 [ 28.020071] ffffffff829f0b10 0000000000000000 ffffffff81f18460ffff88011a81e340 [ 28.020071] Call Trace: [ 28.020071] [<ffffffff8106bd88>] process_one_work+0x1c8/0x540 [ 28.020071] [<ffffffff8106bd0b>] ? process_one_work+0x14b/0x540 [ 28.020071] [<ffffffff8106c214>] worker_thread+0x114/0x460 [ 28.020071] [<ffffffff8106c100>] ? process_one_work+0x540/0x540 [ 28.020071] [<ffffffff81071bf8>] kthread+0xf8/0x110 [ 28.020071] [<ffffffff81071b00>] ?kthread_create_on_node+0x200/0x200 [ 28.020071] [<ffffffff81a6522f>] ret_from_fork+0x3f/0x70 [ 28.020071] [<ffffffff81071b00>] ?kthread_create_on_node+0x200/0x200 Signed-off-by: Shaohua Li <shli@fb.com> Signed-off-by: Tejun Heo <tj@kernel.org> Cc: stable@vger.kernel.org # v2.6.31+

Dmitry Vyukov reported the following using trinity and the memory error detector AddressSanitizer (https://code.google.com/p/address-sanitizer/wiki/AddressSanitizerForKernel). [ 124.575597] ERROR: AddressSanitizer: heap-buffer-overflow on address ffff88002e280000 [ 124.576801] ffff88002e280000 is located 131938492886538 bytes to the left of 28857600-byte region [ffffffff81282e0a, ffffffff82e0830a) [ 124.578633] Accessed by thread T10915: [ 124.579295] inlined in describe_heap_address ./arch/x86/mm/asan/report.c:164 [ 124.579295] #0 ffffffff810dd277 in asan_report_error ./arch/x86/mm/asan/report.c:278 [ 124.580137] #1 ffffffff810dc6a0 in asan_check_region ./arch/x86/mm/asan/asan.c:37 [ 124.581050] #2 ffffffff810dd423 in __tsan_read8 ??:0 [ 124.581893] #3 ffffffff8107c093 in get_wchan ./arch/x86/kernel/process_64.c:444 The address checks in the 64bit implementation of get_wchan() are wrong in several ways: - The lower bound of the stack is not the start of the stack page. It's the start of the stack page plus sizeof (struct thread_info) - The upper bound must be: top_of_stack - TOP_OF_KERNEL_STACK_PADDING - 2 * sizeof(unsigned long). The 2 * sizeof(unsigned long) is required because the stack pointer points at the frame pointer. The layout on the stack is: ... IP FP ... IP FP. So we need to make sure that both IP and FP are in the bounds. Fix the bound checks and get rid of the mix of numeric constants, u64 and unsigned long. Making all unsigned long allows us to use the same function for 32bit as well. Use READ_ONCE() when accessing the stack. This does not prevent a concurrent wakeup of the task and the stack changing, but at least it avoids TOCTOU. Also check task state at the end of the loop. Again that does not prevent concurrent changes, but it avoids walking for nothing. Add proper comments while at it. Reported-by: Dmitry Vyukov <dvyukov@google.com> Reported-by: Sasha Levin <sasha.levin@oracle.com> Based-on-patch-from: Wolfram Gloger <wmglo@dent.med.uni-muenchen.de> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Borislav Petkov <bp@alien8.de> Reviewed-by: Dmitry Vyukov <dvyukov@google.com> Cc: Andrey Ryabinin <ryabinin.a.a@gmail.com> Cc: Andy Lutomirski <luto@amacapital.net> Cc: Andrey Konovalov <andreyknvl@google.com> Cc: Kostya Serebryany <kcc@google.com> Cc: Alexander Potapenko <glider@google.com> Cc: kasan-dev <kasan-dev@googlegroups.com> Cc: Denys Vlasenko <dvlasenk@redhat.com> Cc: Andi Kleen <ak@linux.intel.com> Cc: Wolfram Gloger <wmglo@dent.med.uni-muenchen.de> Cc: stable@vger.kernel.org Link: http://lkml.kernel.org/r/20150930083302.694788319@linutronix.de Signed-off-by: Thomas Gleixner <tglx@linutronix.de>

…fy a fault SunDong reported the following on https://bugzilla.kernel.org/show_bug.cgi?id=103841 I think I find a linux bug, I have the test cases is constructed. I can stable recurring problems in fedora22(4.0.4) kernel version, arch for x86_64. I construct transparent huge page, when the parent and child process with MAP_SHARE, MAP_PRIVATE way to access the same huge page area, it has the opportunity to lead to huge page copy on write failure, and then it will munmap the child corresponding mmap area, but then the child mmap area with VM_MAYSHARE attributes, child process munmap this area can trigger VM_BUG_ON in set_vma_resv_flags functions (vma - > vm_flags & VM_MAYSHARE). There were a number of problems with the report (e.g. it's hugetlbfs that triggers this, not transparent huge pages) but it was fundamentally correct in that a VM_BUG_ON in set_vma_resv_flags() can be triggered that looks like this vma ffff8804651fd0d0 start 00007fc474e00000 end 00007fc475e00000 next ffff8804651fd018 prev ffff8804651fd188 mm ffff88046b1b1800 prot 8000000000000027 anon_vma (null) vm_ops ffffffff8182a7a0 pgoff 0 file ffff88106bdb9800 private_data (null) flags: 0x84400fb(read|write|shared|mayread|maywrite|mayexec|mayshare|dontexpand|hugetlb) ------------ kernel BUG at mm/hugetlb.c:462! SMP Modules linked in: xt_pkttype xt_LOG xt_limit [..] CPU: 38 PID: 26839 Comm: map Not tainted 4.0.4-default #1 Hardware name: Dell Inc. PowerEdge R810/0TT6JF, BIOS 2.7.4 04/26/2012 set_vma_resv_flags+0x2d/0x30 The VM_BUG_ON is correct because private and shared mappings have different reservation accounting but the warning clearly shows that the VMA is shared. When a private COW fails to allocate a new page then only the process that created the VMA gets the page -- all the children unmap the page. If the children access that data in the future then they get killed. The problem is that the same file is mapped shared and private. During the COW, the allocation fails, the VMAs are traversed to unmap the other private pages but a shared VMA is found and the bug is triggered. This patch identifies such VMAs and skips them. Signed-off-by: Mel Gorman <mgorman@techsingularity.net> Reported-by: SunDong <sund_sky@126.com> Reviewed-by: Michal Hocko <mhocko@suse.com> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: Hugh Dickins <hughd@google.com> Cc: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com> Cc: David Rientjes <rientjes@google.com> Reviewed-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Since 9eb1e57 drm/dp/mst: make sure mst_primary mstb is valid in work function we validate the mstb structs in the work function, and doing that takes a reference. So we should never get here with the work function running using the mstb device, only if the work function hasn't run yet or is running for another mstb. So we don't need to sync the work here, this was causing lockdep spew as below. [ +0.000160] ============================================= [ +0.000001] [ INFO: possible recursive locking detected ] [ +0.000002] 3.10.0-320.el7.rhel72.stable.backport.3.x86_64.debug #1 Tainted: G W ------------ [ +0.000001] --------------------------------------------- [ +0.000001] kworker/4:2/1262 is trying to acquire lock: [ +0.000001] ((&mgr->work)){+.+.+.}, at: [<ffffffff810b29a5>] flush_work+0x5/0x2e0 [ +0.000007] but task is already holding lock: [ +0.000001] ((&mgr->work)){+.+.+.}, at: [<ffffffff810b57e4>] process_one_work+0x1b4/0x710 [ +0.000004] other info that might help us debug this: [ +0.000001] Possible unsafe locking scenario: [ +0.000002] CPU0 [ +0.000000] ---- [ +0.000001] lock((&mgr->work)); [ +0.000002] lock((&mgr->work)); [ +0.000001] *** DEADLOCK *** [ +0.000001] May be due to missing lock nesting notation [ +0.000002] 2 locks held by kworker/4:2/1262: [ +0.000001] #0: (events_long){.+.+.+}, at: [<ffffffff810b57e4>] process_one_work+0x1b4/0x710 [ +0.000004] #1: ((&mgr->work)){+.+.+.}, at: [<ffffffff810b57e4>] process_one_work+0x1b4/0x710 [ +0.000003] stack backtrace: [ +0.000003] CPU: 4 PID: 1262 Comm: kworker/4:2 Tainted: G W ------------ 3.10.0-320.el7.rhel72.stable.backport.3.x86_64.debug #1 [ +0.000001] Hardware name: LENOVO 20EGS0R600/20EGS0R600, BIOS GNET71WW (2.19 ) 02/05/2015 [ +0.000008] Workqueue: events_long drm_dp_mst_link_probe_work [drm_kms_helper] [ +0.000001] ffffffff82c26c90 00000000a527b914 ffff88046399bae8 ffffffff816fe04d [ +0.000004] ffff88046399bb58 ffffffff8110f47f ffff880461438000 0001009b840fc003 [ +0.000002] ffff880461438a98 0000000000000000 0000000804dc26e1 ffffffff824a2c00 [ +0.000003] Call Trace: [ +0.000004] [<ffffffff816fe04d>] dump_stack+0x19/0x1b [ +0.000004] [<ffffffff8110f47f>] __lock_acquire+0x115f/0x1250 [ +0.000002] [<ffffffff8110fd49>] lock_acquire+0x99/0x1e0 [ +0.000002] [<ffffffff810b29a5>] ? flush_work+0x5/0x2e0 [ +0.000002] [<ffffffff810b29ee>] flush_work+0x4e/0x2e0 [ +0.000002] [<ffffffff810b29a5>] ? flush_work+0x5/0x2e0 [ +0.000004] [<ffffffff81025905>] ? native_sched_clock+0x35/0x80 [ +0.000002] [<ffffffff81025959>] ? sched_clock+0x9/0x10 [ +0.000002] [<ffffffff810da1f5>] ? local_clock+0x25/0x30 [ +0.000002] [<ffffffff8110dca9>] ? mark_held_locks+0xb9/0x140 [ +0.000003] [<ffffffff810b4ed5>] ? __cancel_work_timer+0x95/0x160 [ +0.000002] [<ffffffff810b4ee8>] __cancel_work_timer+0xa8/0x160 [ +0.000002] [<ffffffff810b4fb0>] cancel_work_sync+0x10/0x20 [ +0.000007] [<ffffffffa0160d17>] drm_dp_destroy_mst_branch_device+0x27/0x120 [drm_kms_helper] [ +0.000006] [<ffffffffa0163968>] drm_dp_mst_link_probe_work+0x78/0xa0 [drm_kms_helper] [ +0.000002] [<ffffffff810b5850>] process_one_work+0x220/0x710 [ +0.000002] [<ffffffff810b57e4>] ? process_one_work+0x1b4/0x710 [ +0.000005] [<ffffffff810b5e5b>] worker_thread+0x11b/0x3a0 [ +0.000003] [<ffffffff810b5d40>] ? process_one_work+0x710/0x710 [ +0.000002] [<ffffffff810beced>] kthread+0xed/0x100 [ +0.000003] [<ffffffff810bec00>] ? insert_kthread_work+0x80/0x80 [ +0.000003] [<ffffffff817121d8>] ret_from_fork+0x58/0x90 v2: add flush_work. Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch> Cc: stable@vger.kernel.org Signed-off-by: Dave Airlie <airlied@redhat.com>

When function graph tracer is enabled, the following operation will trigger panic: mount -t debugfs nodev /sys/kernel echo next_tgid > /sys/kernel/tracing/set_ftrace_filter echo function_graph > /sys/kernel/tracing/current_tracer ls /proc/ ------------[ cut here ]------------ [ 198.501417] Unable to handle kernel paging request at virtual address cb88537fdc8ba316 [ 198.506126] pgd = ffffffc008f79000 [ 198.509363] [cb88537fdc8ba316] *pgd=00000000488c6003, *pud=00000000488c6003, *pmd=0000000000000000 [ 198.517726] Internal error: Oops: 94000005 [#1] SMP [ 198.518798] Modules linked in: [ 198.520582] CPU: 1 PID: 1388 Comm: ls Tainted: G [ 198.521800] Hardware name: linux,dummy-virt (DT) [ 198.522852] task: ffffffc0fa9e8000 ti: ffffffc0f9ab0000 task.ti: ffffffc0f9ab0000 [ 198.524306] PC is at next_tgid+0x30/0x100 [ 198.525205] LR is at return_to_handler+0x0/0x20 [ 198.526090] pc : [<ffffffc0002a1070>] lr : [<ffffffc0000907c0>] pstate: 60000145 [ 198.527392] sp : ffffffc0f9ab3d40 [ 198.528084] x29: ffffffc0f9ab3d40 x28: ffffffc0f9ab0000 [ 198.529406] x27: ffffffc000d6a000 x26: ffffffc000b786e8 [ 198.530659] x25: ffffffc0002a1900 x24: ffffffc0faf16c00 [ 198.531942] x23: ffffffc0f9ab3ea0 x22: 0000000000000002 [ 198.533202] x21: ffffffc000d85050 x20: 0000000000000002 [ 198.534446] x19: 0000000000000002 x18: 0000000000000000 [ 198.535719] x17: 000000000049fa08 x16: ffffffc000242efc [ 198.537030] x15: 0000007fa472b54c x14: ffffffffff000000 [ 198.538347] x13: ffffffc0fada84a0 x12: 0000000000000001 [ 198.539634] x11: ffffffc0f9ab3d70 x10: ffffffc0f9ab3d70 [ 198.540915] x9 : ffffffc0000907c0 x8 : ffffffc0f9ab3d40 [ 198.542215] x7 : 0000002e330f08f0 x6 : 0000000000000015 [ 198.543508] x5 : 0000000000000f08 x4 : ffffffc0f9835ec0 [ 198.544792] x3 : cb88537fdc8ba316 x2 : cb88537fdc8ba306 [ 198.546108] x1 : 0000000000000002 x0 : ffffffc000d85050 [ 198.547432] [ 198.547920] Process ls (pid: 1388, stack limit = 0xffffffc0f9ab0020) [ 198.549170] Stack: (0xffffffc0f9ab3d40 to 0xffffffc0f9ab4000) [ 198.582568] Call trace: [ 198.583313] [<ffffffc0002a1070>] next_tgid+0x30/0x100 [ 198.584359] [<ffffffc0000907bc>] ftrace_graph_caller+0x6c/0x70 [ 198.585503] [<ffffffc0000907bc>] ftrace_graph_caller+0x6c/0x70 [ 198.586574] [<ffffffc0000907bc>] ftrace_graph_caller+0x6c/0x70 [ 198.587660] [<ffffffc0000907bc>] ftrace_graph_caller+0x6c/0x70 [ 198.588896] Code: aa0003f5 2a0103f4 b4000102 91004043 (885f7c60) [ 198.591092] ---[ end trace 6a346f8f20949ac8 ]--- This is because when using function graph tracer, if the traced function return value is in multi regs ([x0-x7]), return_to_handler may corrupt them. So in return_to_handler, the parameter regs should be protected properly. Cc: <stable@vger.kernel.org> # 3.18+ Signed-off-by: Li Bin <huawei.libin@huawei.com> Acked-by: AKASHI Takahiro <takahiro.akashi@linaro.org> Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>

Commit 1a3d595 ("MIPS: Tidy up FPU context switching") removed FP context saving from the asm-written resume function in favour of reusing existing code to perform the same task. However it only removed the FP context saving code from the r4k_switch.S implementation of resume. Octeon uses its own implementation in octeon_switch.S, so remove FP context saving there too in order to prevent attempting to save context twice. That formerly led to an exception from the second save as follows because the FPU had already been disabled by the first save: do_cpu invoked from kernel context![#1]: CPU: 0 PID: 2 Comm: kthreadd Not tainted 4.3.0-rc2-dirty #2 task: 800000041f84a008 ti: 800000041f864000 task.ti: 800000041f864000 $ 0 : 0000000000000000 0000000010008ce1 0000000000100000 ffffffffbfffffff $ 4 : 800000041f84a008 800000041f84ac08 800000041f84c000 0000000000000004 $ 8 : 0000000000000001 0000000000000000 0000000000000000 0000000000000001 $12 : 0000000010008ce3 0000000000119c60 0000000000000036 800000041f864000 $16 : 800000041f84ac08 800000000792ce80 800000041f84a008 ffffffff81758b00 $20 : 0000000000000000 ffffffff8175ae50 0000000000000000 ffffffff8176c740 $24 : 0000000000000006 ffffffff81170300 $28 : 800000041f864000 800000041f867d90 0000000000000000 ffffffff815f3fa0 Hi : 0000000000fa8257 Lo : ffffffffe15cfc00 epc : ffffffff8112821c resume+0x9c/0x200 ra : ffffffff815f3fa0 __schedule+0x3f0/0x7d8 Status: 10008ce2 KX SX UX KERNEL EXL Cause : 1080002c (ExcCode 0b) PrId : 000d0601 (Cavium Octeon+) Modules linked in: Process kthreadd (pid: 2, threadinfo=800000041f864000, task=800000041f84a008, tls=0000000000000000) Stack : ffffffff81604218 ffffffff815f7e08 800000041f84a008 ffffffff811681b0 800000041f84a008 ffffffff817e9878 0000000000000000 ffffffff81770000 ffffffff81768340 ffffffff81161398 0000000000000001 0000000000000000 0000000000000000 ffffffff815f4424 0000000000000000 ffffffff81161d68 ffffffff81161be8 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 ffffffff8111e16c 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 0000000000000000 ... Call Trace: [<ffffffff8112821c>] resume+0x9c/0x200 [<ffffffff815f3fa0>] __schedule+0x3f0/0x7d8 [<ffffffff815f4424>] schedule+0x34/0x98 [<ffffffff81161d68>] kthreadd+0x180/0x198 [<ffffffff8111e16c>] ret_from_kernel_thread+0x14/0x1c Tested using cavium_octeon_defconfig on an EdgeRouter Lite. Fixes: 1a3d595 ("MIPS: Tidy up FPU context switching") Reported-by: Aaro Koskinen <aaro.koskinen@nokia.com> Signed-off-by: Paul Burton <paul.burton@imgtec.com> Cc: linux-mips@linux-mips.org Cc: Aleksey Makarov <aleksey.makarov@auriga.com> Cc: linux-kernel@vger.kernel.org Cc: Chandrakala Chavva <cchavva@caviumnetworks.com> Cc: David Daney <david.daney@cavium.com> Cc: Leonid Rosenboim <lrosenboim@caviumnetworks.com> Patchwork: https://patchwork.linux-mips.org/patch/11166/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

My colleague ran into a program stall on a x86_64 server, where n_tty_read() was waiting for data even if there was data in the buffer in the pty. kernel stack for the stuck process looks like below. #0 [ffff88303d107b58] __schedule at ffffffff815c4b20 #1 [ffff88303d107bd0] schedule at ffffffff815c513e #2 [ffff88303d107bf0] schedule_timeout at ffffffff815c7818 #3 [ffff88303d107ca0] wait_woken at ffffffff81096bd2 #4 [ffff88303d107ce0] n_tty_read at ffffffff8136fa23 #5 [ffff88303d107dd0] tty_read at ffffffff81368013 #6 [ffff88303d107e20] __vfs_read at ffffffff811a3704 #7 [ffff88303d107ec0] vfs_read at ffffffff811a3a57 #8 [ffff88303d107f00] sys_read at ffffffff811a4306 #9 [ffff88303d107f50] entry_SYSCALL_64_fastpath at ffffffff815c86d7 There seems to be two problems causing this issue. First, in drivers/tty/n_tty.c, __receive_buf() stores the data and updates ldata->commit_head using smp_store_release() and then checks the wait queue using waitqueue_active(). However, since there is no memory barrier, __receive_buf() could return without calling wake_up_interactive_poll(), and at the same time, n_tty_read() could start to wait in wait_woken() as in the following chart. __receive_buf() n_tty_read() ------------------------------------------------------------------------ if (waitqueue_active(&tty->read_wait)) /* Memory operations issued after the RELEASE may be completed before the RELEASE operation has completed */ add_wait_queue(&tty->read_wait, &wait); ... if (!input_available_p(tty, 0)) { smp_store_release(&ldata->commit_head, ldata->read_head); ... timeout = wait_woken(&wait, TASK_INTERRUPTIBLE, timeout); ------------------------------------------------------------------------ The second problem is that n_tty_read() also lacks a memory barrier call and could also cause __receive_buf() to return without calling wake_up_interactive_poll(), and n_tty_read() to wait in wait_woken() as in the chart below. __receive_buf() n_tty_read() ------------------------------------------------------------------------ spin_lock_irqsave(&q->lock, flags); /* from add_wait_queue() */ ... if (!input_available_p(tty, 0)) { /* Memory operations issued after the RELEASE may be completed before the RELEASE operation has completed */ smp_store_release(&ldata->commit_head, ldata->read_head); if (waitqueue_active(&tty->read_wait)) __add_wait_queue(q, wait); spin_unlock_irqrestore(&q->lock,flags); /* from add_wait_queue() */ ... timeout = wait_woken(&wait, TASK_INTERRUPTIBLE, timeout); ------------------------------------------------------------------------ There are also other places in drivers/tty/n_tty.c which have similar calls to waitqueue_active(), so instead of adding many memory barrier calls, this patch simply removes the call to waitqueue_active(), leaving just wake_up*() behind. This fixes both problems because, even though the memory access before or after the spinlocks in both wake_up*() and add_wait_queue() can sneak into the critical section, it cannot go past it and the critical section assures that they will be serialized (please see "INTER-CPU ACQUIRING BARRIER EFFECTS" in Documentation/memory-barriers.txt for a better explanation). Moreover, the resulting code is much simpler. Latency measurement using a ping-pong test over a pty doesn't show any visible performance drop. Signed-off-by: Kosuke Tatsukawa <tatsu@ab.jp.nec.com> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Since commit 2b018d5 ("pppoe: drop PPPOX_ZOMBIEs in pppoe_release"), pppoe_release() calls dev_put(po->pppoe_dev) if sk is in the PPPOX_ZOMBIE state. But pppoe_flush_dev() can set sk->sk_state to PPPOX_ZOMBIE _and_ reset po->pppoe_dev to NULL. This leads to the following oops: [ 570.140800] BUG: unable to handle kernel NULL pointer dereference at 00000000000004e0 [ 570.142931] IP: [<ffffffffa018c701>] pppoe_release+0x50/0x101 [pppoe] [ 570.144601] PGD 3d119067 PUD 3dbc1067 PMD 0 [ 570.144601] Oops: 0000 [#1] SMP [ 570.144601] Modules linked in: l2tp_ppp l2tp_netlink l2tp_core ip6_udp_tunnel udp_tunnel pppoe pppox ppp_generic slhc loop crc32c_intel ghash_clmulni_intel jitterentropy_rng sha256_generic hmac drbg ansi_cprng aesni_intel aes_x86_64 ablk_helper cryptd lrw gf128mul glue_helper acpi_cpufreq evdev serio_raw processor button ext4 crc16 mbcache jbd2 virtio_net virtio_blk virtio_pci virtio_ring virtio [ 570.144601] CPU: 1 PID: 15738 Comm: ppp-apitest Not tainted 4.2.0 #1 [ 570.144601] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Debian-1.8.2-1 04/01/2014 [ 570.144601] task: ffff88003d30d600 ti: ffff880036b60000 task.ti: ffff880036b60000 [ 570.144601] RIP: 0010:[<ffffffffa018c701>] [<ffffffffa018c701>] pppoe_release+0x50/0x101 [pppoe] [ 570.144601] RSP: 0018:ffff880036b63e08 EFLAGS: 00010202 [ 570.144601] RAX: 0000000000000000 RBX: ffff880034340000 RCX: 0000000000000206 [ 570.144601] RDX: 0000000000000006 RSI: ffff88003d30dd20 RDI: ffff88003d30dd20 [ 570.144601] RBP: ffff880036b63e28 R08: 0000000000000001 R09: 0000000000000000 [ 570.144601] R10: 00007ffee9b50420 R11: ffff880034340078 R12: ffff8800387ec780 [ 570.144601] R13: ffff8800387ec7b0 R14: ffff88003e222aa0 R15: ffff8800387ec7b0 [ 570.144601] FS: 00007f5672f48700(0000) GS:ffff88003fc80000(0000) knlGS:0000000000000000 [ 570.144601] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 570.144601] CR2: 00000000000004e0 CR3: 0000000037f7e000 CR4: 00000000000406a0 [ 570.144601] Stack: [ 570.144601] ffffffffa018f240 ffff8800387ec780 ffffffffa018f240 ffff8800387ec7b0 [ 570.144601] ffff880036b63e48 ffffffff812caabe ffff880039e4e000 0000000000000008 [ 570.144601] ffff880036b63e58 ffffffff812cabad ffff880036b63ea8 ffffffff811347f5 [ 570.144601] Call Trace: [ 570.144601] [<ffffffff812caabe>] sock_release+0x1a/0x75 [ 570.144601] [<ffffffff812cabad>] sock_close+0xd/0x11 [ 570.144601] [<ffffffff811347f5>] __fput+0xff/0x1a5 [ 570.144601] [<ffffffff811348cb>] ____fput+0x9/0xb [ 570.144601] [<ffffffff81056682>] task_work_run+0x66/0x90 [ 570.144601] [<ffffffff8100189e>] prepare_exit_to_usermode+0x8c/0xa7 [ 570.144601] [<ffffffff81001a26>] syscall_return_slowpath+0x16d/0x19b [ 570.144601] [<ffffffff813babb1>] int_ret_from_sys_call+0x25/0x9f [ 570.144601] Code: 48 8b 83 c8 01 00 00 a8 01 74 12 48 89 df e8 8b 27 14 e1 b8 f7 ff ff ff e9 b7 00 00 00 8a 43 12 a8 0b 74 1c 48 8b 83 a8 04 00 00 <48> 8b 80 e0 04 00 00 65 ff 08 48 c7 83 a8 04 00 00 00 00 00 00 [ 570.144601] RIP [<ffffffffa018c701>] pppoe_release+0x50/0x101 [pppoe] [ 570.144601] RSP <ffff880036b63e08> [ 570.144601] CR2: 00000000000004e0 [ 570.200518] ---[ end trace 46956baf17349563 ]--- pppoe_flush_dev() has no reason to override sk->sk_state with PPPOX_ZOMBIE. pppox_unbind_sock() already sets sk->sk_state to PPPOX_DEAD, which is the correct state given that sk is unbound and po->pppoe_dev is NULL. Fixes: 2b018d5 ("pppoe: drop PPPOX_ZOMBIEs in pppoe_release") Tested-by: Oleksii Berezhniak <core@irc.lg.ua> Signed-off-by: Guillaume Nault <g.nault@alphalink.fr> Signed-off-by: David S. Miller <davem@davemloft.net>

[ Upstream commit 0e16776 ] A race condition was found in sg_proc_debug_helper(). It was observed on a system using an IBM LTO-9 SAS Tape Drive (ULTRIUM-TD9) and monitoring /proc/scsi/sg/debug every second. A very large elapsed time would sometimes appear. This is caused by two race conditions. We reproduced the issue with an IBM ULTRIUM-HH9 tape drive on an x86_64 architecture. A patched kernel was built, and the race condition could not be observed anymore after the application of this patch. A reproducer C program utilising the scsi_debug module was also built by Changhui Zhong and can be viewed here: https://github.com/MichaelRabek/linux-tests/blob/master/drivers/scsi/sg/sg_race_trigger.c The first race happens between the reading of hp->duration in sg_proc_debug_helper() and request completion in sg_rq_end_io(). The hp->duration member variable may hold either of two types of information: #1 - The start time of the request. This value is present while the request is not yet finished. #2 - The total execution time of the request (end_time - start_time). If sg_proc_debug_helper() executes *after* the value of hp->duration was changed from #1 to #2, but *before* srp->done is set to 1 in sg_rq_end_io(), a fresh timestamp is taken in the else branch, and the elapsed time (value type #2) is subtracted from a timestamp, which cannot yield a valid elapsed time (which is a type #2 value as well). To fix this issue, the value of hp->duration must change under the protection of the sfp->rq_list_lock in sg_rq_end_io(). Since sg_proc_debug_helper() takes this read lock, the change to srp->done and srp->header.duration will happen atomically from the perspective of sg_proc_debug_helper() and the race condition is thus eliminated. The second race condition happens between sg_proc_debug_helper() and sg_new_write(). Even though hp->duration is set to the current time stamp in sg_add_request() under the write lock's protection, it gets overwritten by a call to get_sg_io_hdr(), which calls copy_from_user() to copy struct sg_io_hdr from userspace into kernel space. hp->duration is set to the start time again in sg_common_write(). If sg_proc_debug_helper() is called between these two calls, an arbitrary value set by userspace (usually zero) is used to compute the elapsed time. To fix this issue, hp->duration must be set to the current timestamp again after get_sg_io_hdr() returns successfully. A small race window still exists between get_sg_io_hdr() and setting hp->duration, but this window is only a few instructions wide and does not result in observable issues in practice, as confirmed by testing. Additionally, we fix the format specifier from %d to %u for printing unsigned int values in sg_proc_debug_helper(). Signed-off-by: Michal Rábek <mrabek@redhat.com> Suggested-by: Tomas Henzl <thenzl@redhat.com> Tested-by: Changhui Zhong <czhong@redhat.com> Reviewed-by: Ewan D. Milne <emilne@redhat.com> Reviewed-by: John Meneghini <jmeneghi@redhat.com> Reviewed-by: Tomas Henzl <thenzl@redhat.com> Link: https://patch.msgid.link/20251212160900.64924-1-mrabek@redhat.com Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 14adddc ] After resume from suspend to RAM, the following splash is generated if the HDMI driver is probed (independent of a connected cable): [ 1194.484052] irq 80: nobody cared (try booting with the "irqpoll" option) [ 1194.484074] CPU: 0 UID: 0 PID: 627 Comm: rtcwake Not tainted 6.17.0-rc7-g96f1a11414b3 #1 PREEMPT [ 1194.484082] Hardware name: Rockchip RK3576 EVB V10 Board (DT) [ 1194.484085] Call trace: [ 1194.484087] ... (stripped) [ 1194.484283] handlers: [ 1194.484285] [<00000000bc363dcb>] dw_hdmi_qp_main_hardirq [dw_hdmi_qp] [ 1194.484302] Disabling IRQ #80 Apparently the HDMI IP is losing part of its state while the system is suspended and generates spurious interrupts during resume. The bug has not yet been noticed, as system suspend does not yet work properly on upstream kernel with either the Rockchip RK3588 or RK3576 platform. Fixes: 128a9bf ("drm/rockchip: Add basic RK3588 HDMI output support") Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com> Reviewed-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com> Signed-off-by: Heiko Stuebner <heiko@sntech.de> Link: https://patch.msgid.link/20251014-rockchip-hdmi-suspend-fix-v1-1-983fcbf44839@collabora.com Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 1e1f205 ] In btrfs_read_locked_inode() if we fail to lookup the inode, we jump to the 'out' label with a path that has a read locked leaf and then we call iget_failed(). This can result in a ABBA deadlock, since iget_failed() triggers inode eviction and that causes the release of the delayed inode, which must lock the delayed inode's mutex, and a task updating a delayed inode starts by taking the node's mutex and then modifying the inode's subvolume btree. Syzbot reported the following lockdep splat for this: ====================================================== WARNING: possible circular locking dependency detected syzkaller #0 Not tainted ------------------------------------------------------ btrfs-cleaner/8725 is trying to acquire lock: ffff0000d6826a48 (&delayed_node->mutex){+.+.}-{4:4}, at: __btrfs_release_delayed_node+0xa0/0x9b0 fs/btrfs/delayed-inode.c:290 but task is already holding lock: ffff0000dbeba878 (btrfs-tree-00){++++}-{4:4}, at: btrfs_tree_read_lock_nested+0x44/0x2ec fs/btrfs/locking.c:145 which lock already depends on the new lock. the existing dependency chain (in reverse order) is: -> #1 (btrfs-tree-00){++++}-{4:4}: __lock_release kernel/locking/lockdep.c:5574 [inline] lock_release+0x198/0x39c kernel/locking/lockdep.c:5889 up_read+0x24/0x3c kernel/locking/rwsem.c:1632 btrfs_tree_read_unlock+0xdc/0x298 fs/btrfs/locking.c:169 btrfs_tree_unlock_rw fs/btrfs/locking.h:218 [inline] btrfs_search_slot+0xa6c/0x223c fs/btrfs/ctree.c:2133 btrfs_lookup_inode+0xd8/0x38c fs/btrfs/inode-item.c:395 __btrfs_update_delayed_inode+0x124/0xed0 fs/btrfs/delayed-inode.c:1032 btrfs_update_delayed_inode fs/btrfs/delayed-inode.c:1118 [inline] __btrfs_commit_inode_delayed_items+0x15f8/0x1748 fs/btrfs/delayed-inode.c:1141 __btrfs_run_delayed_items+0x1ac/0x514 fs/btrfs/delayed-inode.c:1176 btrfs_run_delayed_items_nr+0x28/0x38 fs/btrfs/delayed-inode.c:1219 flush_space+0x26c/0xb68 fs/btrfs/space-info.c:828 do_async_reclaim_metadata_space+0x110/0x364 fs/btrfs/space-info.c:1158 btrfs_async_reclaim_metadata_space+0x90/0xd8 fs/btrfs/space-info.c:1226 process_one_work+0x7e8/0x155c kernel/workqueue.c:3263 process_scheduled_works kernel/workqueue.c:3346 [inline] worker_thread+0x958/0xed8 kernel/workqueue.c:3427 kthread+0x5fc/0x75c kernel/kthread.c:463 ret_from_fork+0x10/0x20 arch/arm64/kernel/entry.S:844 -> #0 (&delayed_node->mutex){+.+.}-{4:4}: check_prev_add kernel/locking/lockdep.c:3165 [inline] check_prevs_add kernel/locking/lockdep.c:3284 [inline] validate_chain kernel/locking/lockdep.c:3908 [inline] __lock_acquire+0x1774/0x30a4 kernel/locking/lockdep.c:5237 lock_acquire+0x14c/0x2e0 kernel/locking/lockdep.c:5868 __mutex_lock_common+0x1d0/0x2678 kernel/locking/mutex.c:598 __mutex_lock kernel/locking/mutex.c:760 [inline] mutex_lock_nested+0x2c/0x38 kernel/locking/mutex.c:812 __btrfs_release_delayed_node+0xa0/0x9b0 fs/btrfs/delayed-inode.c:290 btrfs_release_delayed_node fs/btrfs/delayed-inode.c:315 [inline] btrfs_remove_delayed_node+0x68/0x84 fs/btrfs/delayed-inode.c:1326 btrfs_evict_inode+0x578/0xe28 fs/btrfs/inode.c:5587 evict+0x414/0x928 fs/inode.c:810 iput_final fs/inode.c:1914 [inline] iput+0x95c/0xad4 fs/inode.c:1966 iget_failed+0xec/0x134 fs/bad_inode.c:248 btrfs_read_locked_inode+0xe1c/0x1234 fs/btrfs/inode.c:4101 btrfs_iget+0x1b0/0x264 fs/btrfs/inode.c:5837 btrfs_run_defrag_inode fs/btrfs/defrag.c:237 [inline] btrfs_run_defrag_inodes+0x520/0xdc4 fs/btrfs/defrag.c:309 cleaner_kthread+0x21c/0x418 fs/btrfs/disk-io.c:1516 kthread+0x5fc/0x75c kernel/kthread.c:463 ret_from_fork+0x10/0x20 arch/arm64/kernel/entry.S:844 other info that might help us debug this: Possible unsafe locking scenario: CPU0 CPU1 ---- ---- rlock(btrfs-tree-00); lock(&delayed_node->mutex); lock(btrfs-tree-00); lock(&delayed_node->mutex); *** DEADLOCK *** 1 lock held by btrfs-cleaner/8725: #0: ffff0000dbeba878 (btrfs-tree-00){++++}-{4:4}, at: btrfs_tree_read_lock_nested+0x44/0x2ec fs/btrfs/locking.c:145 stack backtrace: CPU: 0 UID: 0 PID: 8725 Comm: btrfs-cleaner Not tainted syzkaller #0 PREEMPT Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 10/03/2025 Call trace: show_stack+0x2c/0x3c arch/arm64/kernel/stacktrace.c:499 (C) __dump_stack+0x30/0x40 lib/dump_stack.c:94 dump_stack_lvl+0xd8/0x12c lib/dump_stack.c:120 dump_stack+0x1c/0x28 lib/dump_stack.c:129 print_circular_bug+0x324/0x32c kernel/locking/lockdep.c:2043 check_noncircular+0x154/0x174 kernel/locking/lockdep.c:2175 check_prev_add kernel/locking/lockdep.c:3165 [inline] check_prevs_add kernel/locking/lockdep.c:3284 [inline] validate_chain kernel/locking/lockdep.c:3908 [inline] __lock_acquire+0x1774/0x30a4 kernel/locking/lockdep.c:5237 lock_acquire+0x14c/0x2e0 kernel/locking/lockdep.c:5868 __mutex_lock_common+0x1d0/0x2678 kernel/locking/mutex.c:598 __mutex_lock kernel/locking/mutex.c:760 [inline] mutex_lock_nested+0x2c/0x38 kernel/locking/mutex.c:812 __btrfs_release_delayed_node+0xa0/0x9b0 fs/btrfs/delayed-inode.c:290 btrfs_release_delayed_node fs/btrfs/delayed-inode.c:315 [inline] btrfs_remove_delayed_node+0x68/0x84 fs/btrfs/delayed-inode.c:1326 btrfs_evict_inode+0x578/0xe28 fs/btrfs/inode.c:5587 evict+0x414/0x928 fs/inode.c:810 iput_final fs/inode.c:1914 [inline] iput+0x95c/0xad4 fs/inode.c:1966 iget_failed+0xec/0x134 fs/bad_inode.c:248 btrfs_read_locked_inode+0xe1c/0x1234 fs/btrfs/inode.c:4101 btrfs_iget+0x1b0/0x264 fs/btrfs/inode.c:5837 btrfs_run_defrag_inode fs/btrfs/defrag.c:237 [inline] btrfs_run_defrag_inodes+0x520/0xdc4 fs/btrfs/defrag.c:309 cleaner_kthread+0x21c/0x418 fs/btrfs/disk-io.c:1516 kthread+0x5fc/0x75c kernel/kthread.c:463 ret_from_fork+0x10/0x20 arch/arm64/kernel/entry.S:844 Fix this by releasing the path before calling iget_failed(). Reported-by: syzbot+c1c6edb02bea1da754d8@syzkaller.appspotmail.com Link: https://lore.kernel.org/linux-btrfs/694530c2.a70a0220.207337.010d.GAE@google.com/ Fixes: 6967399 ("btrfs: push cleanup into btrfs_read_locked_inode()") Reviewed-by: Boris Burkov <boris@bur.io> Signed-off-by: Filipe Manana <fdmanana@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit e67c577 ] Analog to commit db5b4e3 ("ip6_gre: make ip6gre_header() robust") Over the years, syzbot found many ways to crash the kernel in ipgre_header() [1]. This involves team or bonding drivers ability to dynamically change their dev->needed_headroom and/or dev->hard_header_len In this particular crash mld_newpack() allocated an skb with a too small reserve/headroom, and by the time mld_sendpack() was called, syzbot managed to attach an ipgre device. [1] skbuff: skb_under_panic: text:ffffffff89ea3cb7 len:2030915468 put:2030915372 head:ffff888058b43000 data:ffff887fdfa6e194 tail:0x120 end:0x6c0 dev:team0 kernel BUG at net/core/skbuff.c:213 ! Oops: invalid opcode: 0000 [#1] SMP KASAN PTI CPU: 1 UID: 0 PID: 1322 Comm: kworker/1:9 Not tainted syzkaller #0 PREEMPT(full) Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 10/25/2025 Workqueue: mld mld_ifc_work RIP: 0010:skb_panic+0x157/0x160 net/core/skbuff.c:213 Call Trace: <TASK> skb_under_panic net/core/skbuff.c:223 [inline] skb_push+0xc3/0xe0 net/core/skbuff.c:2641 ipgre_header+0x67/0x290 net/ipv4/ip_gre.c:897 dev_hard_header include/linux/netdevice.h:3436 [inline] neigh_connected_output+0x286/0x460 net/core/neighbour.c:1618 NF_HOOK_COND include/linux/netfilter.h:307 [inline] ip6_output+0x340/0x550 net/ipv6/ip6_output.c:247 NF_HOOK+0x9e/0x380 include/linux/netfilter.h:318 mld_sendpack+0x8d4/0xe60 net/ipv6/mcast.c:1855 mld_send_cr net/ipv6/mcast.c:2154 [inline] mld_ifc_work+0x83e/0xd60 net/ipv6/mcast.c:2693 process_one_work kernel/workqueue.c:3257 [inline] process_scheduled_works+0xad1/0x1770 kernel/workqueue.c:3340 worker_thread+0x8a0/0xda0 kernel/workqueue.c:3421 kthread+0x711/0x8a0 kernel/kthread.c:463 ret_from_fork+0x510/0xa50 arch/x86/kernel/process.c:158 ret_from_fork_asm+0x1a/0x30 arch/x86/entry/entry_64.S:246 Fixes: c544193 ("GRE: Refactor GRE tunneling code.") Reported-by: syzbot+7c134e1c3aa3283790b9@syzkaller.appspotmail.com Closes: https://www.spinics.net/lists/netdev/msg1147302.html Signed-off-by: Eric Dumazet <edumazet@google.com> Link: https://patch.msgid.link/20260108190214.1667040-1-edumazet@google.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 4dadc40 ] mlx5e_netdev_change_profile can fail to attach a new profile and can fail to rollback to old profile, in such case, we could end up with a dangling netdev with a fully reset netdev_priv. A retry to change profile, e.g. another attempt to call mlx5e_netdev_change_profile via switchdev mode change, will crash trying to access the now NULL priv->mdev. This fix allows mlx5e_netdev_change_profile() to handle previous failures and an empty priv, by not assuming priv is valid. Pass netdev and mdev to all flows requiring mlx5e_netdev_change_profile() and avoid passing priv. In mlx5e_netdev_change_profile() check if current priv is valid, and if not, just attach the new profile without trying to access the old one. This fixes the following oops, when enabling switchdev mode for the 2nd time after first time failure: ## Enabling switchdev mode first time: mlx5_core 0012:03:00.1: E-Switch: Supported tc chains and prios offload workqueue: Failed to create a rescuer kthread for wq "mlx5e": -EINTR mlx5_core 0012:03:00.1: mlx5e_netdev_init_profile:6214:(pid 37199): mlx5e_priv_init failed, err=-12 mlx5_core 0012:03:00.1 gpu3rdma1: mlx5e_netdev_change_profile: new profile init failed, -12 workqueue: Failed to create a rescuer kthread for wq "mlx5e": -EINTR mlx5_core 0012:03:00.1: mlx5e_netdev_init_profile:6214:(pid 37199): mlx5e_priv_init failed, err=-12 mlx5_core 0012:03:00.1 gpu3rdma1: mlx5e_netdev_change_profile: failed to rollback to orig profile, -12 ^^^^^^^^ mlx5_core 0000:00:03.0: E-Switch: Disable: mode(LEGACY), nvfs(0), necvfs(0), active vports(0) ## retry: Enabling switchdev mode 2nd time: mlx5_core 0000:00:03.0: E-Switch: Supported tc chains and prios offload BUG: kernel NULL pointer dereference, address: 0000000000000038 #PF: supervisor read access in kernel mode #PF: error_code(0x0000) - not-present page PGD 0 P4D 0 Oops: Oops: 0000 [#1] SMP NOPTI CPU: 13 UID: 0 PID: 520 Comm: devlink Not tainted 6.18.0-rc4+ #91 PREEMPT(voluntary) Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.16.3-2.fc40 04/01/2014 RIP: 0010:mlx5e_detach_netdev+0x3c/0x90 Code: 50 00 00 f0 80 4f 78 02 48 8b bf e8 07 00 00 48 85 ff 74 16 48 8b 73 78 48 d1 ee 83 e6 01 83 f6 01 40 0f b6 f6 e8 c4 42 00 00 <48> 8b 45 38 48 85 c0 74 08 48 89 df e8 cc 47 40 1e 48 8b bb f0 07 RSP: 0018:ffffc90000673890 EFLAGS: 00010246 RAX: 0000000000000000 RBX: ffff8881036a89c0 RCX: 0000000000000000 RDX: ffff888113f63800 RSI: ffffffff822fe720 RDI: 0000000000000000 RBP: 0000000000000000 R08: 0000000000002dcd R09: 0000000000000000 R10: ffffc900006738e8 R11: 00000000ffffffff R12: 0000000000000000 R13: 0000000000000000 R14: ffff8881036a89c0 R15: 0000000000000000 FS: 00007fdfb8384740(0000) GS:ffff88856a9d6000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000000000000038 CR3: 0000000112ae0005 CR4: 0000000000370ef0 Call Trace: <TASK> mlx5e_netdev_change_profile+0x45/0xb0 mlx5e_vport_rep_load+0x27b/0x2d0 mlx5_esw_offloads_rep_load+0x72/0xf0 esw_offloads_enable+0x5d0/0x970 mlx5_eswitch_enable_locked+0x349/0x430 ? is_mp_supported+0x57/0xb0 mlx5_devlink_eswitch_mode_set+0x26b/0x430 devlink_nl_eswitch_set_doit+0x6f/0xf0 genl_family_rcv_msg_doit+0xe8/0x140 genl_rcv_msg+0x18b/0x290 ? __pfx_devlink_nl_pre_doit+0x10/0x10 ? __pfx_devlink_nl_eswitch_set_doit+0x10/0x10 ? __pfx_devlink_nl_post_doit+0x10/0x10 ? __pfx_genl_rcv_msg+0x10/0x10 netlink_rcv_skb+0x52/0x100 genl_rcv+0x28/0x40 netlink_unicast+0x282/0x3e0 ? __alloc_skb+0xd6/0x190 netlink_sendmsg+0x1f7/0x430 __sys_sendto+0x213/0x220 ? __sys_recvmsg+0x6a/0xd0 __x64_sys_sendto+0x24/0x30 do_syscall_64+0x50/0x1f0 entry_SYSCALL_64_after_hwframe+0x76/0x7e RIP: 0033:0x7fdfb8495047 Fixes: c4d7eb5 ("net/mxl5e: Add change profile method") Signed-off-by: Saeed Mahameed <saeedm@nvidia.com> Reviewed-by: Tariq Toukan <tariqt@nvidia.com> Link: https://patch.msgid.link/20260108212657.25090-2-saeed@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 123eda2 ] mlx5e_priv is an unstable structure that can be memset(0) if profile attaching fails, mlx5e_priv in mlx5e_dev devlink private is used to reference the netdev and mdev associated with that struct. Instead, store netdev directly into mlx5e_dev and get mdev from the containing mlx5_adev aux device structure. This fixes a kernel oops in mlx5e_remove when switchdev mode fails due to change profile failure. $ devlink dev eswitch set pci/0000:00:03.0 mode switchdev Error: mlx5_core: Failed setting eswitch to offloads. dmesg: workqueue: Failed to create a rescuer kthread for wq "mlx5e": -EINTR mlx5_core 0012:03:00.1: mlx5e_netdev_init_profile:6214:(pid 37199): mlx5e_priv_init failed, err=-12 mlx5_core 0012:03:00.1 gpu3rdma1: mlx5e_netdev_change_profile: new profile init failed, -12 workqueue: Failed to create a rescuer kthread for wq "mlx5e": -EINTR mlx5_core 0012:03:00.1: mlx5e_netdev_init_profile:6214:(pid 37199): mlx5e_priv_init failed, err=-12 mlx5_core 0012:03:00.1 gpu3rdma1: mlx5e_netdev_change_profile: failed to rollback to orig profile, -12 $ devlink dev reload pci/0000:00:03.0 ==> oops BUG: kernel NULL pointer dereference, address: 0000000000000520 #PF: supervisor read access in kernel mode #PF: error_code(0x0000) - not-present page PGD 0 P4D 0 Oops: Oops: 0000 [#1] SMP NOPTI CPU: 3 UID: 0 PID: 521 Comm: devlink Not tainted 6.18.0-rc5+ #117 PREEMPT(voluntary) Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.16.3-2.fc40 04/01/2014 RIP: 0010:mlx5e_remove+0x68/0x130 RSP: 0018:ffffc900034838f0 EFLAGS: 00010246 RAX: ffff88810283c380 RBX: ffff888101874400 RCX: ffffffff826ffc45 RDX: 0000000000000000 RSI: 0000000000000001 RDI: 0000000000000000 RBP: ffff888102d789c0 R08: ffff8881007137f0 R09: ffff888100264e10 R10: ffffc90003483898 R11: ffffc900034838a0 R12: ffff888100d261a0 R13: ffff888100d261a0 R14: ffff8881018749a0 R15: ffff888101874400 FS: 00007f8565fea740(0000) GS:ffff88856a759000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000000000000520 CR3: 000000010b11a004 CR4: 0000000000370ef0 Call Trace: <TASK> device_release_driver_internal+0x19c/0x200 bus_remove_device+0xc6/0x130 device_del+0x160/0x3d0 ? devl_param_driverinit_value_get+0x2d/0x90 mlx5_detach_device+0x89/0xe0 mlx5_unload_one_devl_locked+0x3a/0x70 mlx5_devlink_reload_down+0xc8/0x220 devlink_reload+0x7d/0x260 devlink_nl_reload_doit+0x45b/0x5a0 genl_family_rcv_msg_doit+0xe8/0x140 Fixes: ee75f1f ("net/mlx5e: Create separate devlink instance for ethernet auxiliary device") Fixes: c4d7eb5 ("net/mxl5e: Add change profile method") Signed-off-by: Saeed Mahameed <saeedm@nvidia.com> Link: https://patch.msgid.link/20260108212657.25090-3-saeed@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 4ef8512 ] mlx5e_priv is an unstable structure that can be memset(0) if profile attaching fails. Pass netdev to mlx5e_destroy_netdev() to guarantee it will work on a valid netdev. On mlx5e_remove: Check validity of priv->profile, before attempting to cleanup any resources that might be not there. This fixes a kernel oops in mlx5e_remove when switchdev mode fails due to change profile failure. $ devlink dev eswitch set pci/0000:00:03.0 mode switchdev Error: mlx5_core: Failed setting eswitch to offloads. dmesg: workqueue: Failed to create a rescuer kthread for wq "mlx5e": -EINTR mlx5_core 0012:03:00.1: mlx5e_netdev_init_profile:6214:(pid 37199): mlx5e_priv_init failed, err=-12 mlx5_core 0012:03:00.1 gpu3rdma1: mlx5e_netdev_change_profile: new profile init failed, -12 workqueue: Failed to create a rescuer kthread for wq "mlx5e": -EINTR mlx5_core 0012:03:00.1: mlx5e_netdev_init_profile:6214:(pid 37199): mlx5e_priv_init failed, err=-12 mlx5_core 0012:03:00.1 gpu3rdma1: mlx5e_netdev_change_profile: failed to rollback to orig profile, -12 $ devlink dev reload pci/0000:00:03.0 ==> oops BUG: kernel NULL pointer dereference, address: 0000000000000370 PGD 0 P4D 0 Oops: Oops: 0000 [#1] SMP NOPTI CPU: 15 UID: 0 PID: 520 Comm: devlink Not tainted 6.18.0-rc5+ #115 PREEMPT(voluntary) Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.16.3-2.fc40 04/01/2014 RIP: 0010:mlx5e_dcbnl_dscp_app+0x23/0x100 RSP: 0018:ffffc9000083f8b8 EFLAGS: 00010286 RAX: ffff8881126fc380 RBX: ffff8881015ac400 RCX: ffffffff826ffc45 RDX: 0000000000000000 RSI: 0000000000000001 RDI: ffff8881035109c0 RBP: ffff8881035109c0 R08: ffff888101e3e838 R09: ffff888100264e10 R10: ffffc9000083f898 R11: ffffc9000083f8a0 R12: ffff888101b921a0 R13: ffff888101b921a0 R14: ffff8881015ac9a0 R15: ffff8881015ac400 FS: 00007f789a3c8740(0000) GS:ffff88856aa59000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000000000000370 CR3: 000000010b6c0001 CR4: 0000000000370ef0 Call Trace: <TASK> mlx5e_remove+0x57/0x110 device_release_driver_internal+0x19c/0x200 bus_remove_device+0xc6/0x130 device_del+0x160/0x3d0 ? devl_param_driverinit_value_get+0x2d/0x90 mlx5_detach_device+0x89/0xe0 mlx5_unload_one_devl_locked+0x3a/0x70 mlx5_devlink_reload_down+0xc8/0x220 devlink_reload+0x7d/0x260 devlink_nl_reload_doit+0x45b/0x5a0 genl_family_rcv_msg_doit+0xe8/0x140 Fixes: c4d7eb5 ("net/mxl5e: Add change profile method") Signed-off-by: Saeed Mahameed <saeedm@nvidia.com> Reviewed-by: Shay Drori <shayd@nvidia.com> Reviewed-by: Tariq Toukan <tariqt@nvidia.com> Link: https://patch.msgid.link/20260108212657.25090-4-saeed@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>

commit e707c59 upstream. The Secondary Sample Point Source field has been set to an incorrect value by some mistake in the past 0b01 - SSP_SRC_NO_SSP - SSP is not used. for data bitrates above 1 MBit/s. The correct/default value already used for lower bitrates is 0b00 - SSP_SRC_MEAS_N_OFFSET - SSP position = TRV_DELAY (Measured Transmitter delay) + SSP_OFFSET. The related configuration register structure is described in section 3.1.46 SSP_CFG of the CTU CAN FD IP CORE Datasheet. The analysis leading to the proper configuration is described in section 2.8.3 Secondary sampling point of the datasheet. The change has been tested on AMD/Xilinx Zynq with the next CTU CN FD IP core versions: - 2.6 aka master in the "integration with Zynq-7000 system" test 6.12.43-rt12+ #1 SMP PREEMPT_RT kernel with CTU CAN FD git driver (change already included in the driver repo) - older 2.5 snapshot with mainline kernels with this patch applied locally in the multiple CAN latency tester nightly runs 6.18.0-rc4-rt3-dut #1 SMP PREEMPT_RT 6.19.0-rc3-dut The logs, the datasheet and sources are available at https://canbus.pages.fel.cvut.cz/ Signed-off-by: Ondrej Ille <ondrej.ille@gmail.com> Signed-off-by: Pavel Pisa <pisa@fel.cvut.cz> Link: https://patch.msgid.link/20260105111620.16580-1-pisa@fel.cvut.cz Fixes: 2dcb8e8 ("can: ctucanfd: add support for CTU CAN FD open-source IP core - bus independent part.") Cc: stable@vger.kernel.org Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 038a102 upstream. The kernel test robot has reported: BUG: spinlock trylock failure on UP on CPU#0, kcompactd0/28 lock: 0xffff888807e35ef0, .magic: dead4ead, .owner: kcompactd0/28, .owner_cpu: 0 CPU: 0 UID: 0 PID: 28 Comm: kcompactd0 Not tainted 6.18.0-rc5-00127-ga06157804399 #1 PREEMPT 8cc09ef94dcec767faa911515ce9e609c45db470 Call Trace: <IRQ> __dump_stack (lib/dump_stack.c:95) dump_stack_lvl (lib/dump_stack.c:123) dump_stack (lib/dump_stack.c:130) spin_dump (kernel/locking/spinlock_debug.c:71) do_raw_spin_trylock (kernel/locking/spinlock_debug.c:?) _raw_spin_trylock (include/linux/spinlock_api_smp.h:89 kernel/locking/spinlock.c:138) __free_frozen_pages (mm/page_alloc.c:2973) ___free_pages (mm/page_alloc.c:5295) __free_pages (mm/page_alloc.c:5334) tlb_remove_table_rcu (include/linux/mm.h:? include/linux/mm.h:3122 include/asm-generic/tlb.h:220 mm/mmu_gather.c:227 mm/mmu_gather.c:290) ? __cfi_tlb_remove_table_rcu (mm/mmu_gather.c:289) ? rcu_core (kernel/rcu/tree.c:?) rcu_core (include/linux/rcupdate.h:341 kernel/rcu/tree.c:2607 kernel/rcu/tree.c:2861) rcu_core_si (kernel/rcu/tree.c:2879) handle_softirqs (arch/x86/include/asm/jump_label.h:36 include/trace/events/irq.h:142 kernel/softirq.c:623) __irq_exit_rcu (arch/x86/include/asm/jump_label.h:36 kernel/softirq.c:725) irq_exit_rcu (kernel/softirq.c:741) sysvec_apic_timer_interrupt (arch/x86/kernel/apic/apic.c:1052) </IRQ> <TASK> RIP: 0010:_raw_spin_unlock_irqrestore (arch/x86/include/asm/preempt.h:95 include/linux/spinlock_api_smp.h:152 kernel/locking/spinlock.c:194) free_pcppages_bulk (mm/page_alloc.c:1494) drain_pages_zone (include/linux/spinlock.h:391 mm/page_alloc.c:2632) __drain_all_pages (mm/page_alloc.c:2731) drain_all_pages (mm/page_alloc.c:2747) kcompactd (mm/compaction.c:3115) kthread (kernel/kthread.c:465) ? __cfi_kcompactd (mm/compaction.c:3166) ? __cfi_kthread (kernel/kthread.c:412) ret_from_fork (arch/x86/kernel/process.c:164) ? __cfi_kthread (kernel/kthread.c:412) ret_from_fork_asm (arch/x86/entry/entry_64.S:255) </TASK> Matthew has analyzed the report and identified that in drain_page_zone() we are in a section protected by spin_lock(&pcp->lock) and then get an interrupt that attempts spin_trylock() on the same lock. The code is designed to work this way without disabling IRQs and occasionally fail the trylock with a fallback. However, the SMP=n spinlock implementation assumes spin_trylock() will always succeed, and thus it's normally a no-op. Here the enabled lock debugging catches the problem, but otherwise it could cause a corruption of the pcp structure. The problem has been introduced by commit 5749077 ("mm/page_alloc: leave IRQs enabled for per-cpu page allocations"). The pcp locking scheme recognizes the need for disabling IRQs to prevent nesting spin_trylock() sections on SMP=n, but the need to prevent the nesting in spin_lock() has not been recognized. Fix it by introducing local wrappers that change the spin_lock() to spin_lock_iqsave() with SMP=n and use them in all places that do spin_lock(&pcp->lock). [vbabka@suse.cz: add pcp_ prefix to the spin_lock_irqsave wrappers, per Steven] Link: https://lkml.kernel.org/r/20260105-fix-pcp-up-v1-1-5579662d2071@suse.cz Fixes: 5749077 ("mm/page_alloc: leave IRQs enabled for per-cpu page allocations") Signed-off-by: Vlastimil Babka <vbabka@suse.cz> Reported-by: kernel test robot <oliver.sang@intel.com> Closes: https://lore.kernel.org/oe-lkp/202512101320.e2f2dd6f-lkp@intel.com Analyzed-by: Matthew Wilcox <willy@infradead.org> Link: https://lore.kernel.org/all/aUW05pyc9nZkvY-1@casper.infradead.org/ Acked-by: Mel Gorman <mgorman@techsingularity.net> Cc: Brendan Jackman <jackmanb@google.com> Cc: Johannes Weiner <hannes@cmpxchg.org> Cc: Michal Hocko <mhocko@suse.com> Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Suren Baghdasaryan <surenb@google.com> Cc: Zi Yan <ziy@nvidia.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 2515071 upstream. The GET_INSTANCE_ID macro that caused a kernel panic when accessing sysfs attributes: 1. Off-by-one error: The loop condition used '<=' instead of '<', causing access beyond array bounds. Since array indices are 0-based and go from 0 to instances_count-1, the loop should use '<'. 2. Missing NULL check: The code dereferenced attr_name_kobj->name without checking if attr_name_kobj was NULL, causing a null pointer dereference in min_length_show() and other attribute show functions. The panic occurred when fwupd tried to read BIOS configuration attributes: Oops: general protection fault [#1] SMP KASAN NOPTI KASAN: null-ptr-deref in range [0x0000000000000000-0x0000000000000007] RIP: 0010:min_length_show+0xcf/0x1d0 [hp_bioscfg] Add a NULL check for attr_name_kobj before dereferencing and corrects the loop boundary to match the pattern used elsewhere in the driver. Cc: stable@vger.kernel.org Fixes: 5f94f18 ("platform/x86: hp-bioscfg: bioscfg-h") Signed-off-by: Mario Limonciello <mario.limonciello@amd.com> Link: https://patch.msgid.link/20260115203725.828434-3-mario.limonciello@amd.com Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit ca1a47c upstream. Patch series "mm/hugetlb: fixes for PMD table sharing (incl. using mmu_gather)", v3. One functional fix, one performance regression fix, and two related comment fixes. I cleaned up my prototype I recently shared [1] for the performance fix, deferring most of the cleanups I had in the prototype to a later point. While doing that I identified the other things. The goal of this patch set is to be backported to stable trees "fairly" easily. At least patch #1 and #4. Patch #1 fixes hugetlb_pmd_shared() not detecting any sharing Patch #2 + #3 are simple comment fixes that patch #4 interacts with. Patch #4 is a fix for the reported performance regression due to excessive IPI broadcasts during fork()+exit(). The last patch is all about TLB flushes, IPIs and mmu_gather. Read: complicated There are plenty of cleanups in the future to be had + one reasonable optimization on x86. But that's all out of scope for this series. Runtime tested, with a focus on fixing the performance regression using the original reproducer [2] on x86. This patch (of 4): We switched from (wrongly) using the page count to an independent shared count. Now, shared page tables have a refcount of 1 (excluding speculative references) and instead use ptdesc->pt_share_count to identify sharing. We didn't convert hugetlb_pmd_shared(), so right now, we would never detect a shared PMD table as such, because sharing/unsharing no longer touches the refcount of a PMD table. Page migration, like mbind() or migrate_pages() would allow for migrating folios mapped into such shared PMD tables, even though the folios are not exclusive. In smaps we would account them as "private" although they are "shared", and we would be wrongly setting the PM_MMAP_EXCLUSIVE in the pagemap interface. Fix it by properly using ptdesc_pmd_is_shared() in hugetlb_pmd_shared(). Link: https://lkml.kernel.org/r/20251223214037.580860-1-david@kernel.org Link: https://lkml.kernel.org/r/20251223214037.580860-2-david@kernel.org Link: https://lore.kernel.org/all/8cab934d-4a56-44aa-b641-bfd7e23bd673@kernel.org/ [1] Link: https://lore.kernel.org/all/8cab934d-4a56-44aa-b641-bfd7e23bd673@kernel.org/ [2] Fixes: 59d9094 ("mm: hugetlb: independent PMD page table shared count") Signed-off-by: David Hildenbrand (Red Hat) <david@kernel.org> Reviewed-by: Rik van Riel <riel@surriel.com> Reviewed-by: Lance Yang <lance.yang@linux.dev> Tested-by: Lance Yang <lance.yang@linux.dev> Reviewed-by: Harry Yoo <harry.yoo@oracle.com> Tested-by: Laurence Oberman <loberman@redhat.com> Reviewed-by: Lorenzo Stoakes <lorenzo.stoakes@oracle.com> Acked-by: Oscar Salvador <osalvador@suse.de> Cc: Liu Shixin <liushixin2@huawei.com> Cc: Uschakow, Stanislav" <suschako@amazon.de> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

…gs list [ Upstream commit b97d5ee ] The netdevsim driver lacks a protection mechanism for operations on the bpf_bound_progs list. When the nsim_bpf_create_prog() performs list_add_tail, it is possible that nsim_bpf_destroy_prog() is simultaneously performs list_del. Concurrent operations on the list may lead to list corruption and trigger a kernel crash as follows: [ 417.290971] kernel BUG at lib/list_debug.c:62! [ 417.290983] invalid opcode: 0000 [#1] PREEMPT SMP NOPTI [ 417.290992] CPU: 10 PID: 168 Comm: kworker/10:1 Kdump: loaded Not tainted 6.19.0-rc5 #1 [ 417.291003] Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.16.3-debian-1.16.3-2 04/01/2014 [ 417.291007] Workqueue: events bpf_prog_free_deferred [ 417.291021] RIP: 0010:__list_del_entry_valid_or_report+0xa7/0xc0 [ 417.291034] Code: a8 ff 0f 0b 48 89 fe 48 89 ca 48 c7 c7 48 a1 eb ae e8 ed fb a8 ff 0f 0b 48 89 fe 48 89 c2 48 c7 c7 80 a1 eb ae e8 d9 fb a8 ff <0f> 0b 48 89 d1 48 c7 c7 d0 a1 eb ae 48 89 f2 48 89 c6 e8 c2 fb a8 [ 417.291040] RSP: 0018:ffffb16a40807df8 EFLAGS: 00010246 [ 417.291046] RAX: 000000000000006d RBX: ffff8e589866f500 RCX: 0000000000000000 [ 417.291051] RDX: 0000000000000000 RSI: ffff8e59f7b23180 RDI: ffff8e59f7b23180 [ 417.291055] RBP: ffffb16a412c9000 R08: 0000000000000000 R09: 0000000000000003 [ 417.291059] R10: ffffb16a40807c80 R11: ffffffffaf9edce8 R12: ffff8e594427ac20 [ 417.291063] R13: ffff8e59f7b44780 R14: ffff8e58800b7a05 R15: 0000000000000000 [ 417.291074] FS: 0000000000000000(0000) GS:ffff8e59f7b00000(0000) knlGS:0000000000000000 [ 417.291079] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 417.291083] CR2: 00007fc4083efe08 CR3: 00000001c3626006 CR4: 0000000000770ee0 [ 417.291088] PKRU: 55555554 [ 417.291091] Call Trace: [ 417.291096] <TASK> [ 417.291103] nsim_bpf_destroy_prog+0x31/0x80 [netdevsim] [ 417.291154] __bpf_prog_offload_destroy+0x2a/0x80 [ 417.291163] bpf_prog_dev_bound_destroy+0x6f/0xb0 [ 417.291171] bpf_prog_free_deferred+0x18e/0x1a0 [ 417.291178] process_one_work+0x18a/0x3a0 [ 417.291188] worker_thread+0x27b/0x3a0 [ 417.291197] ? __pfx_worker_thread+0x10/0x10 [ 417.291207] kthread+0xe5/0x120 [ 417.291214] ? __pfx_kthread+0x10/0x10 [ 417.291221] ret_from_fork+0x31/0x50 [ 417.291230] ? __pfx_kthread+0x10/0x10 [ 417.291236] ret_from_fork_asm+0x1a/0x30 [ 417.291246] </TASK> Add a mutex lock, to prevent simultaneous addition and deletion operations on the list. Fixes: 31d3ad8 ("netdevsim: add bpf offload support") Reported-by: Yinhao Hu <dddddd@hust.edu.cn> Reported-by: Kaiyan Mei <M202472210@hust.edu.cn> Signed-off-by: Yun Lu <luyun@kylinos.cn> Link: https://patch.msgid.link/20260116095308.11441-1-luyun_611@163.com Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>

…itives [ Upstream commit c06343b ] The "valid" readout delay between the two reads of the watchdog is larger than the valid delta between the resulting watchdog and clocksource intervals, which results in false positive watchdog results. Assume TSC is the clocksource and HPET is the watchdog and both have a uncertainty margin of 250us (default). The watchdog readout does: 1) wdnow = read(HPET); 2) csnow = read(TSC); 3) wdend = read(HPET); The valid window for the delta between #1 and #3 is calculated by the uncertainty margins of the watchdog and the clocksource: m = 2 * watchdog.uncertainty_margin + cs.uncertainty margin; which results in 750us for the TSC/HPET case. The actual interval comparison uses a smaller margin: m = watchdog.uncertainty_margin + cs.uncertainty margin; which results in 500us for the TSC/HPET case. That means the following scenario will trigger the watchdog: Watchdog cycle N: 1) wdnow[N] = read(HPET); 2) csnow[N] = read(TSC); 3) wdend[N] = read(HPET); Assume the delay between #1 and #2 is 100us and the delay between #1 and Watchdog cycle N + 1: 4) wdnow[N + 1] = read(HPET); 5) csnow[N + 1] = read(TSC); 6) wdend[N + 1] = read(HPET); If the delay between #4 and #6 is within the 750us margin then any delay between #4 and #5 which is larger than 600us will fail the interval check and mark the TSC unstable because the intervals are calculated against the previous value: wd_int = wdnow[N + 1] - wdnow[N]; cs_int = csnow[N + 1] - csnow[N]; Putting the above delays in place this results in: cs_int = (wdnow[N + 1] + 610us) - (wdnow[N] + 100us); -> cs_int = wd_int + 510us; which is obviously larger than the allowed 500us margin and results in marking TSC unstable. Fix this by using the same margin as the interval comparison. If the delay between two watchdog reads is larger than that, then the readout was either disturbed by interconnect congestion, NMIs or SMIs. Fixes: 4ac1dd3 ("clocksource: Set cs_watchdog_read() checks based on .uncertainty_margin") Reported-by: Daniel J Blueman <daniel@quora.org> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Paul E. McKenney <paulmck@kernel.org> Tested-by: Paul E. McKenney <paulmck@kernel.org> Link: https://lore.kernel.org/lkml/20250602223251.496591-1-daniel@quora.org/ Link: https://patch.msgid.link/87bjjxc9dq.ffs@tglx Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 27880b0 ] tcf_ife_encode() must make sure ife_encode() does not return NULL. syzbot reported: Oops: general protection fault, probably for non-canonical address 0xdffffc0000000000: 0000 [#1] SMP KASAN NOPTI KASAN: null-ptr-deref in range [0x0000000000000000-0x0000000000000007] RIP: 0010:ife_tlv_meta_encode+0x41/0xa0 net/ife/ife.c:166 CPU: 3 UID: 0 PID: 8990 Comm: syz.0.696 Not tainted syzkaller #0 PREEMPT(full) Call Trace: <TASK> ife_encode_meta_u32+0x153/0x180 net/sched/act_ife.c:101 tcf_ife_encode net/sched/act_ife.c:841 [inline] tcf_ife_act+0x1022/0x1de0 net/sched/act_ife.c:877 tc_act include/net/tc_wrapper.h:130 [inline] tcf_action_exec+0x1c0/0xa20 net/sched/act_api.c:1152 tcf_exts_exec include/net/pkt_cls.h:349 [inline] mall_classify+0x1a0/0x2a0 net/sched/cls_matchall.c:42 tc_classify include/net/tc_wrapper.h:197 [inline] __tcf_classify net/sched/cls_api.c:1764 [inline] tcf_classify+0x7f2/0x1380 net/sched/cls_api.c:1860 multiq_classify net/sched/sch_multiq.c:39 [inline] multiq_enqueue+0xe0/0x510 net/sched/sch_multiq.c:66 dev_qdisc_enqueue+0x45/0x250 net/core/dev.c:4147 __dev_xmit_skb net/core/dev.c:4262 [inline] __dev_queue_xmit+0x2998/0x46c0 net/core/dev.c:4798 Fixes: 295a6e0 ("net/sched: act_ife: Change to use ife module") Reported-by: syzbot+5cf914f193dffde3bd3c@syzkaller.appspotmail.com Closes: https://lore.kernel.org/netdev/6970d61d.050a0220.706b.0010.GAE@google.com/T/#u Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Yotam Gigi <yotam.gi@gmail.com> Reviewed-by: Jamal Hadi Salim <jhs@mojatatu.com> Link: https://patch.msgid.link/20260121133724.3400020-1-edumazet@google.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 4a3dba4 ] firmware populates MAC address, link modes (supported, advertised) and EEPROM data in shared firmware structure which kernel access via MAC block(CGX/RPM). Accessing fwdata, on boards booted with out MAC block leading to kernel panics. Internal error: Oops: 0000000096000005 [#1] SMP [ 10.460721] Modules linked in: [ 10.463779] CPU: 0 UID: 0 PID: 174 Comm: kworker/0:3 Not tainted 6.19.0-rc5-00154-g76ec646abdf7-dirty #3 PREEMPT [ 10.474045] Hardware name: Marvell OcteonTX CN98XX board (DT) [ 10.479793] Workqueue: events work_for_cpu_fn [ 10.484159] pstate: 80400009 (Nzcv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--) [ 10.491124] pc : rvu_sdp_init+0x18/0x114 [ 10.495051] lr : rvu_probe+0xe58/0x1d18 Fixes: 9978144 ("Octeontx2-af: Fetch MAC channel info from firmware") Fixes: 5f21226 ("Octeontx2-pf: ethtool: support multi advertise mode") Signed-off-by: Hariprasad Kelam <hkelam@marvell.com> Link: https://patch.msgid.link/20260121094819.2566786-1-hkelam@marvell.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>

commit ea8ccfd upstream. The code to restore a ZA context doesn't attempt to allocate the task's sve_state before setting TIF_SME. Consequently, restoring a ZA context can place a task into an invalid state where TIF_SME is set but the task's sve_state is NULL. In legitimate but uncommon cases where the ZA signal context was NOT created by the kernel in the context of the same task (e.g. if the task is saved/restored with something like CRIU), we have no guarantee that sve_state had been allocated previously. In these cases, userspace can enter streaming mode without trapping while sve_state is NULL, causing a later NULL pointer dereference when the kernel attempts to store the register state: | # ./sigreturn-za | Unable to handle kernel NULL pointer dereference at virtual address 0000000000000000 | Mem abort info: | ESR = 0x0000000096000046 | EC = 0x25: DABT (current EL), IL = 32 bits | SET = 0, FnV = 0 | EA = 0, S1PTW = 0 | FSC = 0x06: level 2 translation fault | Data abort info: | ISV = 0, ISS = 0x00000046, ISS2 = 0x00000000 | CM = 0, WnR = 1, TnD = 0, TagAccess = 0 | GCS = 0, Overlay = 0, DirtyBit = 0, Xs = 0 | user pgtable: 4k pages, 52-bit VAs, pgdp=0000000101f47c00 | [0000000000000000] pgd=08000001021d8403, p4d=0800000102274403, pud=0800000102275403, pmd=0000000000000000 | Internal error: Oops: 0000000096000046 [#1] SMP | Modules linked in: | CPU: 0 UID: 0 PID: 153 Comm: sigreturn-za Not tainted 6.19.0-rc1 #1 PREEMPT | Hardware name: linux,dummy-virt (DT) | pstate: 214000c9 (nzCv daIF +PAN -UAO -TCO +DIT -SSBS BTYPE=--) | pc : sve_save_state+0x4/0xf0 | lr : fpsimd_save_user_state+0xb0/0x1c0 | sp : ffff80008070bcc0 | x29: ffff80008070bcc0 x28: fff00000c1ca4c40 x27: 63cfa172fb5cf658 | x26: fff00000c1ca5228 x25: 0000000000000000 x24: 0000000000000000 | x23: 0000000000000000 x22: fff00000c1ca4c40 x21: fff00000c1ca4c40 | x20: 0000000000000020 x19: fff00000ff6900f0 x18: 0000000000000000 | x17: fff05e8e0311f000 x16: 0000000000000000 x15: 028fca8f3bdaf21c | x14: 0000000000000212 x13: fff00000c0209f10 x12: 0000000000000020 | x11: 0000000000200b20 x10: 0000000000000000 x9 : fff00000ff69dcc0 | x8 : 00000000000003f2 x7 : 0000000000000001 x6 : fff00000c1ca5b48 | x5 : fff05e8e0311f000 x4 : 0000000008000000 x3 : 0000000000000000 | x2 : 0000000000000001 x1 : fff00000c1ca5970 x0 : 0000000000000440 | Call trace: | sve_save_state+0x4/0xf0 (P) | fpsimd_thread_switch+0x48/0x198 | __switch_to+0x20/0x1c0 | __schedule+0x36c/0xce0 | schedule+0x34/0x11c | exit_to_user_mode_loop+0x124/0x188 | el0_interrupt+0xc8/0xd8 | __el0_irq_handler_common+0x18/0x24 | el0t_64_irq_handler+0x10/0x1c | el0t_64_irq+0x198/0x19c | Code: 54000040 d51b4408 d65f03c0 d503245f (e5bb5800) | ---[ end trace 0000000000000000 ]--- Fix this by having restore_za_context() ensure that the task's sve_state is allocated, matching what we do when taking an SME trap. Any live SVE/SSVE state (which is restored earlier from a separate signal context) must be preserved, and hence this is not zeroed. Fixes: 3978221 ("arm64/sme: Implement ZA signal handling") Signed-off-by: Mark Rutland <mark.rutland@arm.com> Cc: <stable@vger.kernel.org> Cc: Mark Brown <broonie@kernel.org> Cc: Will Deacon <will@kernel.org> Reviewed-by: Mark Brown <broonie@kernel.org> Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit e2f8216 upstream. A DABT is reported[1] on an android based system when resume from hiberate. This happens because swsusp_arch_suspend_exit() is marked with SYM_CODE_*() and does not have a CFI hash, but swsusp_arch_resume() will attempt to verify the CFI hash when calling a copy of swsusp_arch_suspend_exit(). Given that there's an existing requirement that the entrypoint to swsusp_arch_suspend_exit() is the first byte of the .hibernate_exit.text section, we cannot fix this by marking swsusp_arch_suspend_exit() with SYM_FUNC_*(). The simplest fix for now is to disable the CFI check in swsusp_arch_resume(). Mark swsusp_arch_resume() as __nocfi to disable the CFI check. [1] [ 22.991934][ T1] Unable to handle kernel paging request at virtual address 0000000109170ffc [ 22.991934][ T1] Mem abort info: [ 22.991934][ T1] ESR = 0x0000000096000007 [ 22.991934][ T1] EC = 0x25: DABT (current EL), IL = 32 bits [ 22.991934][ T1] SET = 0, FnV = 0 [ 22.991934][ T1] EA = 0, S1PTW = 0 [ 22.991934][ T1] FSC = 0x07: level 3 translation fault [ 22.991934][ T1] Data abort info: [ 22.991934][ T1] ISV = 0, ISS = 0x00000007, ISS2 = 0x00000000 [ 22.991934][ T1] CM = 0, WnR = 0, TnD = 0, TagAccess = 0 [ 22.991934][ T1] GCS = 0, Overlay = 0, DirtyBit = 0, Xs = 0 [ 22.991934][ T1] [0000000109170ffc] user address but active_mm is swapper [ 22.991934][ T1] Internal error: Oops: 0000000096000007 [#1] PREEMPT SMP [ 22.991934][ T1] Dumping ftrace buffer: [ 22.991934][ T1] (ftrace buffer empty) [ 22.991934][ T1] Modules linked in: [ 22.991934][ T1] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 6.6.98-android15-8-g0b1d2aee7fc3-dirty-4k #1 688c7060a825a3ac418fe53881730b355915a419 [ 22.991934][ T1] Hardware name: Unisoc UMS9360-base Board (DT) [ 22.991934][ T1] pstate: 804000c5 (Nzcv daIF +PAN -UAO -TCO -DIT -SSBS BTYPE=--) [ 22.991934][ T1] pc : swsusp_arch_resume+0x2ac/0x344 [ 22.991934][ T1] lr : swsusp_arch_resume+0x294/0x344 [ 22.991934][ T1] sp : ffffffc08006b960 [ 22.991934][ T1] x29: ffffffc08006b9c0 x28: 0000000000000000 x27: 0000000000000000 [ 22.991934][ T1] x26: 0000000000000000 x25: 0000000000000000 x24: 0000000000000820 [ 22.991934][ T1] x23: ffffffd0817e3000 x22: ffffffd0817e3000 x21: 0000000000000000 [ 22.991934][ T1] x20: ffffff8089171000 x19: ffffffd08252c8c8 x18: ffffffc080061058 [ 22.991934][ T1] x17: 00000000529c6ef0 x16: 00000000529c6ef0 x15: 0000000000000004 [ 22.991934][ T1] x14: ffffff8178c88000 x13: 0000000000000006 x12: 0000000000000000 [ 22.991934][ T1] x11: 0000000000000015 x10: 0000000000000001 x9 : ffffffd082533000 [ 22.991934][ T1] x8 : 0000000109171000 x7 : 205b5d3433393139 x6 : 392e32322020205b [ 22.991934][ T1] x5 : 000000010916f000 x4 : 000000008164b000 x3 : ffffff808a4e0530 [ 22.991934][ T1] x2 : ffffffd08058e784 x1 : 0000000082326000 x0 : 000000010a283000 [ 22.991934][ T1] Call trace: [ 22.991934][ T1] swsusp_arch_resume+0x2ac/0x344 [ 22.991934][ T1] hibernation_restore+0x158/0x18c [ 22.991934][ T1] load_image_and_restore+0xb0/0xec [ 22.991934][ T1] software_resume+0xf4/0x19c [ 22.991934][ T1] software_resume_initcall+0x34/0x78 [ 22.991934][ T1] do_one_initcall+0xe8/0x370 [ 22.991934][ T1] do_initcall_level+0xc8/0x19c [ 22.991934][ T1] do_initcalls+0x70/0xc0 [ 22.991934][ T1] do_basic_setup+0x1c/0x28 [ 22.991934][ T1] kernel_init_freeable+0xe0/0x148 [ 22.991934][ T1] kernel_init+0x20/0x1a8 [ 22.991934][ T1] ret_from_fork+0x10/0x20 [ 22.991934][ T1] Code: a9400a61 f94013e0 f9438923 f9400a64 (b85fc110) Co-developed-by: Jeson Gao <jeson.gao@unisoc.com> Signed-off-by: Jeson Gao <jeson.gao@unisoc.com> Signed-off-by: Zhaoyang Huang <zhaoyang.huang@unisoc.com> Acked-by: Will Deacon <will@kernel.org> Acked-by: Mark Rutland <mark.rutland@arm.com> Cc: <stable@vger.kernel.org> [catalin.marinas@arm.com: commit log updated by Mark Rutland] Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 90f9f5d upstream. When creating a synthetic event based on an existing synthetic event that had a stacktrace field and the new synthetic event used that field a kernel crash occurred: ~# cd /sys/kernel/tracing ~# echo 's:stack unsigned long stack[];' > dynamic_events ~# echo 'hist:keys=prev_pid:s0=common_stacktrace if prev_state & 3' >> events/sched/sched_switch/trigger ~# echo 'hist:keys=next_pid:s1=$s0:onmatch(sched.sched_switch).trace(stack,$s1)' >> events/sched/sched_switch/trigger The above creates a synthetic event that takes a stacktrace when a task schedules out in a non-running state and passes that stacktrace to the sched_switch event when that task schedules back in. It triggers the "stack" synthetic event that has a stacktrace as its field (called "stack"). ~# echo 's:syscall_stack s64 id; unsigned long stack[];' >> dynamic_events ~# echo 'hist:keys=common_pid:s2=stack' >> events/synthetic/stack/trigger ~# echo 'hist:keys=common_pid:s3=$s2,i0=id:onmatch(synthetic.stack).trace(syscall_stack,$i0,$s3)' >> events/raw_syscalls/sys_exit/trigger The above makes another synthetic event called "syscall_stack" that attaches the first synthetic event (stack) to the sys_exit trace event and records the stacktrace from the stack event with the id of the system call that is exiting. When enabling this event (or using it in a historgram): ~# echo 1 > events/synthetic/syscall_stack/enable Produces a kernel crash! BUG: unable to handle page fault for address: 0000000000400010 #PF: supervisor read access in kernel mode #PF: error_code(0x0000) - not-present page PGD 0 P4D 0 Oops: Oops: 0000 [#1] SMP PTI CPU: 6 UID: 0 PID: 1257 Comm: bash Not tainted 6.16.3+deb14-amd64 #1 PREEMPT(lazy) Debian 6.16.3-1 Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.17.0-debian-1.17.0-1 04/01/2014 RIP: 0010:trace_event_raw_event_synth+0x90/0x380 Code: c5 00 00 00 00 85 d2 0f 84 e1 00 00 00 31 db eb 34 0f 1f 00 66 66 2e 0f 1f 84 00 00 00 00 00 66 66 2e 0f 1f 84 00 00 00 00 00 <49> 8b 04 24 48 83 c3 01 8d 0c c5 08 00 00 00 01 cd 41 3b 5d 40 0f RSP: 0018:ffffd2670388f958 EFLAGS: 00010202 RAX: ffff8ba1065cc100 RBX: 0000000000000000 RCX: 0000000000000000 RDX: 0000000000000001 RSI: fffff266ffda7b90 RDI: ffffd2670388f9b0 RBP: 0000000000000010 R08: ffff8ba104e76000 R09: ffffd2670388fa50 R10: ffff8ba102dd42e0 R11: ffffffff9a908970 R12: 0000000000400010 R13: ffff8ba10a246400 R14: ffff8ba10a710220 R15: fffff266ffda7b90 FS: 00007fa3bc63f740(0000) GS:ffff8ba2e0f48000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000000000400010 CR3: 0000000107f9e003 CR4: 0000000000172ef0 Call Trace: <TASK> ? __tracing_map_insert+0x208/0x3a0 action_trace+0x67/0x70 event_hist_trigger+0x633/0x6d0 event_triggers_call+0x82/0x130 trace_event_buffer_commit+0x19d/0x250 trace_event_raw_event_sys_exit+0x62/0xb0 syscall_exit_work+0x9d/0x140 do_syscall_64+0x20a/0x2f0 ? trace_event_raw_event_sched_switch+0x12b/0x170 ? save_fpregs_to_fpstate+0x3e/0x90 ? _raw_spin_unlock+0xe/0x30 ? finish_task_switch.isra.0+0x97/0x2c0 ? __rseq_handle_notify_resume+0xad/0x4c0 ? __schedule+0x4b8/0xd00 ? restore_fpregs_from_fpstate+0x3c/0x90 ? switch_fpu_return+0x5b/0xe0 ? do_syscall_64+0x1ef/0x2f0 ? do_fault+0x2e9/0x540 ? __handle_mm_fault+0x7d1/0xf70 ? count_memcg_events+0x167/0x1d0 ? handle_mm_fault+0x1d7/0x2e0 ? do_user_addr_fault+0x2c3/0x7f0 entry_SYSCALL_64_after_hwframe+0x76/0x7e The reason is that the stacktrace field is not labeled as such, and is treated as a normal field and not as a dynamic event that it is. In trace_event_raw_event_synth() the event is field is still treated as a dynamic array, but the retrieval of the data is considered a normal field, and the reference is just the meta data: // Meta data is retrieved instead of a dynamic array str_val = (char *)(long)var_ref_vals[val_idx]; // Then when it tries to process it: len = *((unsigned long *)str_val) + 1; It triggers a kernel page fault. To fix this, first when defining the fields of the first synthetic event, set the filter type to FILTER_STACKTRACE. This is used later by the second synthetic event to know that this field is a stacktrace. When creating the field of the new synthetic event, have it use this FILTER_STACKTRACE to know to create a stacktrace field to copy the stacktrace into. Cc: stable@vger.kernel.org Cc: Masami Hiramatsu <mhiramat@kernel.org> Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com> Cc: Tom Zanussi <zanussi@kernel.org> Link: https://patch.msgid.link/20260122194824.6905a38e@gandalf.local.home Fixes: 00cf3d6 ("tracing: Allow synthetic events to pass around stacktraces") Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 9910159 ] When one iio device is a consumer of another, it is possible that the ->info_exist_lock of both ends up being taken when reading the value of the consumer device. Since they currently belong to the same lockdep class (being initialized in a single location with mutex_init()), that results in a lockdep warning CPU0 ---- lock(&iio_dev_opaque->info_exist_lock); lock(&iio_dev_opaque->info_exist_lock); *** DEADLOCK *** May be due to missing lock nesting notation 4 locks held by sensors/414: #0: c31fd6dc (&p->lock){+.+.}-{3:3}, at: seq_read_iter+0x44/0x4e4 #1: c4f5a1c4 (&of->mutex){+.+.}-{3:3}, at: kernfs_seq_start+0x1c/0xac #2: c2827548 (kn->active#34){.+.+}-{0:0}, at: kernfs_seq_start+0x30/0xac #3: c1dd2b6 (&iio_dev_opaque->info_exist_lock){+.+.}-{3:3}, at: iio_read_channel_processed_scale+0x24/0xd8 stack backtrace: CPU: 0 UID: 0 PID: 414 Comm: sensors Not tainted 6.17.11 #5 NONE Hardware name: Generic AM33XX (Flattened Device Tree) Call trace: unwind_backtrace from show_stack+0x10/0x14 show_stack from dump_stack_lvl+0x44/0x60 dump_stack_lvl from print_deadlock_bug+0x2b8/0x334 print_deadlock_bug from __lock_acquire+0x13a4/0x2ab0 __lock_acquire from lock_acquire+0xd0/0x2c0 lock_acquire from __mutex_lock+0xa0/0xe8c __mutex_lock from mutex_lock_nested+0x1c/0x24 mutex_lock_nested from iio_read_channel_raw+0x20/0x6c iio_read_channel_raw from rescale_read_raw+0x128/0x1c4 rescale_read_raw from iio_channel_read+0xe4/0xf4 iio_channel_read from iio_read_channel_processed_scale+0x6c/0xd8 iio_read_channel_processed_scale from iio_hwmon_read_val+0x68/0xbc iio_hwmon_read_val from dev_attr_show+0x18/0x48 dev_attr_show from sysfs_kf_seq_show+0x80/0x110 sysfs_kf_seq_show from seq_read_iter+0xdc/0x4e4 seq_read_iter from vfs_read+0x238/0x2e4 vfs_read from ksys_read+0x6c/0xec ksys_read from ret_fast_syscall+0x0/0x1c Just as the mlock_key already has its own lockdep class, add a lock_class_key for the info_exist mutex. Note that this has in theory been a problem since before IIO first left staging, but it only occurs when a chain of consumers is in use and that is not often done. Fixes: ac917a8 ("staging:iio:core set the iio_dev.info pointer to null on unregister under lock.") Signed-off-by: Rasmus Villemoes <ravi@prevas.dk> Reviewed-by: Peter Rosin <peda@axentia.se> Cc: <stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit e9acda5 ] Fix a use-after-free which happens due to enslave failure after the new slave has been added to the array. Since the new slave can be used for Tx immediately, we can use it after it has been freed by the enslave error cleanup path which frees the allocated slave memory. Slave update array is supposed to be called last when further enslave failures are not expected. Move it after xdp setup to avoid any problems. It is very easy to reproduce the problem with a simple xdp_pass prog: ip l add bond1 type bond mode balance-xor ip l set bond1 up ip l set dev bond1 xdp object xdp_pass.o sec xdp_pass ip l add dumdum type dummy Then run in parallel: while :; do ip l set dumdum master bond1 1>/dev/null 2>&1; done; mausezahn bond1 -a own -b rand -A rand -B 1.1.1.1 -c 0 -t tcp "dp=1-1023, flags=syn" The crash happens almost immediately: [ 605.602850] Oops: general protection fault, probably for non-canonical address 0xe0e6fc2460000137: 0000 [#1] SMP KASAN NOPTI [ 605.602916] KASAN: maybe wild-memory-access in range [0x07380123000009b8-0x07380123000009bf] [ 605.602946] CPU: 0 UID: 0 PID: 2445 Comm: mausezahn Kdump: loaded Tainted: G B 6.19.0-rc6+ #21 PREEMPT(voluntary) [ 605.602979] Tainted: [B]=BAD_PAGE [ 605.602998] Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.16.3-debian-1.16.3-2 04/01/2014 [ 605.603032] RIP: 0010:netdev_core_pick_tx+0xcd/0x210 [ 605.603063] Code: 48 89 fa 48 c1 ea 03 80 3c 02 00 0f 85 3e 01 00 00 48 b8 00 00 00 00 00 fc ff df 4c 8b 6b 08 49 8d 7d 30 48 89 fa 48 c1 ea 03 <80> 3c 02 00 0f 85 25 01 00 00 49 8b 45 30 4c 89 e2 48 89 ee 48 89 [ 605.603111] RSP: 0018:ffff88817b9af348 EFLAGS: 00010213 [ 605.603145] RAX: dffffc0000000000 RBX: ffff88817d28b420 RCX: 0000000000000000 [ 605.603172] RDX: 00e7002460000137 RSI: 0000000000000008 RDI: 07380123000009be [ 605.603199] RBP: ffff88817b541a00 R08: 0000000000000001 R09: fffffbfff3ed8c0c [ 605.603226] R10: ffffffff9f6c6067 R11: 0000000000000001 R12: 0000000000000000 [ 605.603253] R13: 073801230000098e R14: ffff88817d28b448 R15: ffff88817b541a84 [ 605.603286] FS: 00007f6570ef67c0(0000) GS:ffff888221dfa000(0000) knlGS:0000000000000000 [ 605.603319] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 605.603343] CR2: 00007f65712fae40 CR3: 000000011371b000 CR4: 0000000000350ef0 [ 605.603373] Call Trace: [ 605.603392] <TASK> [ 605.603410] __dev_queue_xmit+0x448/0x32a0 [ 605.603434] ? __pfx_vprintk_emit+0x10/0x10 [ 605.603461] ? __pfx_vprintk_emit+0x10/0x10 [ 605.603484] ? __pfx___dev_queue_xmit+0x10/0x10 [ 605.603507] ? bond_start_xmit+0xbfb/0xc20 [bonding] [ 605.603546] ? _printk+0xcb/0x100 [ 605.603566] ? __pfx__printk+0x10/0x10 [ 605.603589] ? bond_start_xmit+0xbfb/0xc20 [bonding] [ 605.603627] ? add_taint+0x5e/0x70 [ 605.603648] ? add_taint+0x2a/0x70 [ 605.603670] ? end_report.cold+0x51/0x75 [ 605.603693] ? bond_start_xmit+0xbfb/0xc20 [bonding] [ 605.603731] bond_start_xmit+0x623/0xc20 [bonding] Fixes: 9e2ee5c ("net, bonding: Add XDP support to the bonding driver") Signed-off-by: Nikolay Aleksandrov <razor@blackwall.org> Reported-by: Chen Zhen <chenzhen126@huawei.com> Closes: https://lore.kernel.org/netdev/fae17c21-4940-5605-85b2-1d5e17342358@huawei.com/ CC: Jussi Maki <joamaki@gmail.com> CC: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Daniel Borkmann <daniel@iogearbox.net> Link: https://patch.msgid.link/20260123120659.571187-1-razor@blackwall.org Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 9bb30be ] Add NULL pointer checks in ice_vsi_set_napi_queues() to prevent crashes during resume from suspend when rings[q_idx]->q_vector is NULL. Tested adaptor: 60:00.0 Ethernet controller [0200]: Intel Corporation Ethernet Controller E810-XXV for SFP [8086:159b] (rev 02) Subsystem: Intel Corporation Ethernet Network Adapter E810-XXV-2 [8086:4003] SR-IOV state: both disabled and enabled can reproduce this issue. kernel version: v6.18 Reproduce steps: Boot up and execute suspend like systemctl suspend or rtcwake. Log: <1>[ 231.443607] BUG: kernel NULL pointer dereference, address: 0000000000000040 <1>[ 231.444052] #PF: supervisor read access in kernel mode <1>[ 231.444484] #PF: error_code(0x0000) - not-present page <6>[ 231.444913] PGD 0 P4D 0 <4>[ 231.445342] Oops: Oops: 0000 [#1] SMP NOPTI <4>[ 231.446635] RIP: 0010:netif_queue_set_napi+0xa/0x170 <4>[ 231.447067] Code: 31 f6 31 ff c3 cc cc cc cc 0f 1f 80 00 00 00 00 90 90 90 90 90 90 90 90 90 90 90 90 90 90 90 90 0f 1f 44 00 00 48 85 c9 74 0b <48> 83 79 30 00 0f 84 39 01 00 00 55 41 89 d1 49 89 f8 89 f2 48 89 <4>[ 231.447513] RSP: 0018:ffffcc780fc078c0 EFLAGS: 00010202 <4>[ 231.447961] RAX: ffff8b848ca30400 RBX: ffff8b848caf2028 RCX: 0000000000000010 <4>[ 231.448443] RDX: 0000000000000000 RSI: 0000000000000000 RDI: ffff8b848dbd4000 <4>[ 231.448896] RBP: ffffcc780fc078e8 R08: 0000000000000000 R09: 0000000000000000 <4>[ 231.449345] R10: 0000000000000000 R11: 0000000000000000 R12: 0000000000000001 <4>[ 231.449817] R13: ffff8b848dbd4000 R14: ffff8b84833390c8 R15: 0000000000000000 <4>[ 231.450265] FS: 00007c7b29e9d740(0000) GS:ffff8b8c068e2000(0000) knlGS:0000000000000000 <4>[ 231.450715] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 <4>[ 231.451179] CR2: 0000000000000040 CR3: 000000030626f004 CR4: 0000000000f72ef0 <4>[ 231.451629] PKRU: 55555554 <4>[ 231.452076] Call Trace: <4>[ 231.452549] <TASK> <4>[ 231.452996] ? ice_vsi_set_napi_queues+0x4d/0x110 [ice] <4>[ 231.453482] ice_resume+0xfd/0x220 [ice] <4>[ 231.453977] ? __pfx_pci_pm_resume+0x10/0x10 <4>[ 231.454425] pci_pm_resume+0x8c/0x140 <4>[ 231.454872] ? __pfx_pci_pm_resume+0x10/0x10 <4>[ 231.455347] dpm_run_callback+0x5f/0x160 <4>[ 231.455796] ? dpm_wait_for_superior+0x107/0x170 <4>[ 231.456244] device_resume+0x177/0x270 <4>[ 231.456708] dpm_resume+0x209/0x2f0 <4>[ 231.457151] dpm_resume_end+0x15/0x30 <4>[ 231.457596] suspend_devices_and_enter+0x1da/0x2b0 <4>[ 231.458054] enter_state+0x10e/0x570 Add defensive checks for both the ring pointer and its q_vector before dereferencing, allowing the system to resume successfully even when q_vectors are unmapped. Fixes: 2a5dc09 ("ice: move netif_queue_set_napi to rtnl-protected sections") Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com> Signed-off-by: Aaron Ma <aaron.ma@canonical.com> Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit f676669 ] When deleting TC steering flows, iterate only over actual devcom peers instead of assuming all possible ports exist. This avoids touching non-existent peers and ensures cleanup is limited to devices the driver is currently connected to. BUG: kernel NULL pointer dereference, address: 0000000000000008 #PF: supervisor write access in kernel mode #PF: error_code(0x0002) - not-present page PGD 133c8a067 P4D 0 Oops: Oops: 0002 [#1] SMP CPU: 19 UID: 0 PID: 2169 Comm: tc Not tainted 6.18.0+ #156 NONE Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.16.0-0-gd239552ce722-prebuilt.qemu.org 04/01/2014 RIP: 0010:mlx5e_tc_del_fdb_peers_flow+0xbe/0x200 [mlx5_core] Code: 00 00 a8 08 74 a8 49 8b 46 18 f6 c4 02 74 9f 4c 8d bf a0 12 00 00 4c 89 ff e8 0e e7 96 e1 49 8b 44 24 08 49 8b 0c 24 4c 89 ff <48> 89 41 08 48 89 08 49 89 2c 24 49 89 5c 24 08 e8 7d ce 96 e1 49 RSP: 0018:ff11000143867528 EFLAGS: 00010246 RAX: 0000000000000000 RBX: dead000000000122 RCX: 0000000000000000 RDX: ff11000143691580 RSI: ff110001026e5000 RDI: ff11000106f3d2a0 RBP: dead000000000100 R08: 00000000000003fd R09: 0000000000000002 R10: ff11000101c75690 R11: ff1100085faea178 R12: ff11000115f0ae78 R13: 0000000000000000 R14: ff11000115f0a800 R15: ff11000106f3d2a0 FS: 00007f35236bf740(0000) GS:ff110008dc809000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000000000000008 CR3: 0000000157a01001 CR4: 0000000000373eb0 Call Trace: <TASK> mlx5e_tc_del_flow+0x46/0x270 [mlx5_core] mlx5e_flow_put+0x25/0x50 [mlx5_core] mlx5e_delete_flower+0x2a6/0x3e0 [mlx5_core] tc_setup_cb_reoffload+0x20/0x80 fl_reoffload+0x26f/0x2f0 [cls_flower] ? mlx5e_tc_reoffload_flows_work+0xc0/0xc0 [mlx5_core] ? mlx5e_tc_reoffload_flows_work+0xc0/0xc0 [mlx5_core] tcf_block_playback_offloads+0x9e/0x1c0 tcf_block_unbind+0x7b/0xd0 tcf_block_setup+0x186/0x1d0 tcf_block_offload_cmd.isra.0+0xef/0x130 tcf_block_offload_unbind+0x43/0x70 __tcf_block_put+0x85/0x160 ingress_destroy+0x32/0x110 [sch_ingress] __qdisc_destroy+0x44/0x100 qdisc_graft+0x22b/0x610 tc_get_qdisc+0x183/0x4d0 rtnetlink_rcv_msg+0x2d7/0x3d0 ? rtnl_calcit.isra.0+0x100/0x100 netlink_rcv_skb+0x53/0x100 netlink_unicast+0x249/0x320 ? __alloc_skb+0x102/0x1f0 netlink_sendmsg+0x1e3/0x420 __sock_sendmsg+0x38/0x60 ____sys_sendmsg+0x1ef/0x230 ? copy_msghdr_from_user+0x6c/0xa0 ___sys_sendmsg+0x7f/0xc0 ? ___sys_recvmsg+0x8a/0xc0 ? __sys_sendto+0x119/0x180 __sys_sendmsg+0x61/0xb0 do_syscall_64+0x55/0x640 entry_SYSCALL_64_after_hwframe+0x4b/0x53 RIP: 0033:0x7f35238bb764 Code: 15 b9 86 0c 00 f7 d8 64 89 02 b8 ff ff ff ff eb bf 0f 1f 44 00 00 f3 0f 1e fa 80 3d e5 08 0d 00 00 74 13 b8 2e 00 00 00 0f 05 <48> 3d 00 f0 ff ff 77 4c c3 0f 1f 00 55 48 89 e5 48 83 ec 20 89 55 RSP: 002b:00007ffed4c35638 EFLAGS: 00000202 ORIG_RAX: 000000000000002e RAX: ffffffffffffffda RBX: 000055a2efcc75e0 RCX: 00007f35238bb764 RDX: 0000000000000000 RSI: 00007ffed4c356a0 RDI: 0000000000000003 RBP: 00007ffed4c35710 R08: 0000000000000010 R09: 00007f3523984b20 R10: 0000000000000004 R11: 0000000000000202 R12: 00007ffed4c35790 R13: 000000006947df8f R14: 000055a2efcc75e0 R15: 00007ffed4c35780 Fixes: 9be6c21 ("net/mlx5e: Handle offloads flows per peer") Signed-off-by: Mark Bloch <mbloch@nvidia.com> Reviewed-by: Shay Drori <shayd@nvidia.com> Signed-off-by: Tariq Toukan <tariqt@nvidia.com> Reviewed-by: Simon Horman <horms@kernel.org> Link: https://patch.msgid.link/1769411695-18820-3-git-send-email-tariqt@nvidia.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 2aa1545 ] Since the commit 25c6a5a ("net: phy: micrel: Dynamically control external clock of KSZ PHY"), the clock of Micrel PHY has been enabled by phy_driver::resume() and disabled by phy_driver::suspend(). However, devm_clk_get_optional_enabled() is used in kszphy_probe(), so the clock will automatically be disabled when the device is unbound from the bus. Therefore, this could cause the clock to be disabled twice, resulting in clk driver warnings. For example, this issue can be reproduced on i.MX6ULL platform, and we can see the following logs when removing the FEC MAC drivers. $ echo 2188000.ethernet > /sys/bus/platform/drivers/fec/unbind $ echo 20b4000.ethernet > /sys/bus/platform/drivers/fec/unbind [ 109.758207] ------------[ cut here ]------------ [ 109.758240] WARNING: drivers/clk/clk.c:1188 at clk_core_disable+0xb4/0xd0, CPU#0: sh/639 [ 109.771011] enet2_ref already disabled [ 109.793359] Call trace: [ 109.822006] clk_core_disable from clk_disable+0x28/0x34 [ 109.827340] clk_disable from clk_disable_unprepare+0xc/0x18 [ 109.833029] clk_disable_unprepare from devm_clk_release+0x1c/0x28 [ 109.839241] devm_clk_release from devres_release_all+0x98/0x100 [ 109.845278] devres_release_all from device_unbind_cleanup+0xc/0x70 [ 109.851571] device_unbind_cleanup from device_release_driver_internal+0x1a4/0x1f4 [ 109.859170] device_release_driver_internal from bus_remove_device+0xbc/0xe4 [ 109.866243] bus_remove_device from device_del+0x140/0x458 [ 109.871757] device_del from phy_mdio_device_remove+0xc/0x24 [ 109.877452] phy_mdio_device_remove from mdiobus_unregister+0x40/0xac [ 109.883918] mdiobus_unregister from fec_enet_mii_remove+0x40/0x78 [ 109.890125] fec_enet_mii_remove from fec_drv_remove+0x4c/0x158 [ 109.896076] fec_drv_remove from device_release_driver_internal+0x17c/0x1f4 [ 109.962748] WARNING: drivers/clk/clk.c:1047 at clk_core_unprepare+0xfc/0x13c, CPU#0: sh/639 [ 109.975805] enet2_ref already unprepared [ 110.002866] Call trace: [ 110.031758] clk_core_unprepare from clk_unprepare+0x24/0x2c [ 110.037440] clk_unprepare from devm_clk_release+0x1c/0x28 [ 110.042957] devm_clk_release from devres_release_all+0x98/0x100 [ 110.048989] devres_release_all from device_unbind_cleanup+0xc/0x70 [ 110.055280] device_unbind_cleanup from device_release_driver_internal+0x1a4/0x1f4 [ 110.062877] device_release_driver_internal from bus_remove_device+0xbc/0xe4 [ 110.069950] bus_remove_device from device_del+0x140/0x458 [ 110.075469] device_del from phy_mdio_device_remove+0xc/0x24 [ 110.081165] phy_mdio_device_remove from mdiobus_unregister+0x40/0xac [ 110.087632] mdiobus_unregister from fec_enet_mii_remove+0x40/0x78 [ 110.093836] fec_enet_mii_remove from fec_drv_remove+0x4c/0x158 [ 110.099782] fec_drv_remove from device_release_driver_internal+0x17c/0x1f4 After analyzing the process of removing the FEC driver, as shown below, it can be seen that the clock was disabled twice by the PHY driver. fec_drv_remove() --> fec_enet_close() --> phy_stop() --> phy_suspend() --> kszphy_suspend() #1 The clock is disabled --> fec_enet_mii_remove() --> mdiobus_unregister() --> phy_mdio_device_remove() --> device_del() --> devm_clk_release() #2 The clock is disabled again Therefore, devm_clk_get_optional() is used to fix the above issue. And to avoid the issue mentioned by the commit 9853294 ("net: phy: micrel: use devm_clk_get_optional_enabled for the rmii-ref clock"), the clock is enabled by clk_prepare_enable() to get the correct clock rate. Fixes: 25c6a5a ("net: phy: micrel: Dynamically control external clock of KSZ PHY") Signed-off-by: Wei Fang <wei.fang@nxp.com> Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com> Link: https://patch.msgid.link/20260126081544.983517-1-wei.fang@nxp.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit a8f930b ] HCA CAP structure is allocated in mlx5_hca_caps_alloc(). mlx5_mdev_init() mlx5_hca_caps_alloc() And HCA CAP is read from the device in mlx5_init_one(). The vhca_id's debugfs file is published even before above two operations are done. Due to this when user reads the vhca id before the initialization, following call trace is observed. Fix this by deferring debugfs publication until the HCA CAP is allocated and read from the device. BUG: kernel NULL pointer dereference, address: 0000000000000004 PGD 0 P4D 0 Oops: Oops: 0000 [#1] SMP PTI CPU: 23 UID: 0 PID: 6605 Comm: cat Kdump: loaded Not tainted 6.18.0-rc7-sf+ #110 PREEMPT(full) Hardware name: Supermicro SYS-6028U-TR4+/X10DRU-i+, BIOS 2.0b 08/09/2016 RIP: 0010:vhca_id_show+0x17/0x30 [mlx5_core] Code: cb 66 90 90 90 90 90 90 90 90 90 90 90 90 90 90 90 90 90 0f 1f 44 00 00 48 8b 47 70 48 c7 c6 45 f0 12 c1 48 8b 80 70 03 00 00 <8b> 50 04 0f ca 0f b7 d2 e8 8c 82 47 cb 31 c0 c3 cc cc cc cc 0f 1f RSP: 0018:ffffd37f4f337d40 EFLAGS: 00010203 RAX: 0000000000000000 RBX: ffff8f18445c9b40 RCX: 0000000000000001 RDX: ffff8f1109825180 RSI: ffffffffc112f045 RDI: ffff8f18445c9b40 RBP: 0000000000000000 R08: 0000645eac0d2928 R09: 0000000000000006 R10: ffffd37f4f337d48 R11: 0000000000000000 R12: ffffd37f4f337dd8 R13: ffffd37f4f337db0 R14: ffff8f18445c9b68 R15: 0000000000000001 FS: 00007f3eea099580(0000) GS:ffff8f2090f1f000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000000000000004 CR3: 00000008b64e4006 CR4: 00000000003726f0 Call Trace: <TASK> seq_read_iter+0x11f/0x4f0 ? _raw_spin_unlock+0x15/0x30 ? do_anonymous_page+0x104/0x810 seq_read+0xf6/0x120 ? srso_alias_untrain_ret+0x1/0x10 full_proxy_read+0x5c/0x90 vfs_read+0xad/0x320 ? handle_mm_fault+0x1ab/0x290 ksys_read+0x52/0xd0 do_syscall_64+0x61/0x11e0 entry_SYSCALL_64_after_hwframe+0x76/0x7e Fixes: dd3dd72 ("net/mlx5: Expose vhca_id to debugfs") Signed-off-by: Parav Pandit <parav@nvidia.com> Reviewed-by: Shay Drori <shayd@nvidia.com> Reviewed-by: Simon Horman <horms@kernel.org> Signed-off-by: Tariq Toukan <tariqt@nvidia.com> Link: https://patch.msgid.link/1769503961-124173-4-git-send-email-tariqt@nvidia.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>

commit b5cbacd upstream. Fix PROCMAP_QUERY to fetch optional build ID only after dropping mmap_lock or per-VMA lock, whichever was used to lock VMA under question, to avoid deadlock reported by syzbot: -> #1 (&mm->mmap_lock){++++}-{4:4}: __might_fault+0xed/0x170 _copy_to_iter+0x118/0x1720 copy_page_to_iter+0x12d/0x1e0 filemap_read+0x720/0x10a0 blkdev_read_iter+0x2b5/0x4e0 vfs_read+0x7f4/0xae0 ksys_read+0x12a/0x250 do_syscall_64+0xcb/0xf80 entry_SYSCALL_64_after_hwframe+0x77/0x7f -> #0 (&sb->s_type->i_mutex_key#8){++++}-{4:4}: __lock_acquire+0x1509/0x26d0 lock_acquire+0x185/0x340 down_read+0x98/0x490 blkdev_read_iter+0x2a7/0x4e0 __kernel_read+0x39a/0xa90 freader_fetch+0x1d5/0xa80 __build_id_parse.isra.0+0xea/0x6a0 do_procmap_query+0xd75/0x1050 procfs_procmap_ioctl+0x7a/0xb0 __x64_sys_ioctl+0x18e/0x210 do_syscall_64+0xcb/0xf80 entry_SYSCALL_64_after_hwframe+0x77/0x7f other info that might help us debug this: Possible unsafe locking scenario: CPU0 CPU1 ---- ---- rlock(&mm->mmap_lock); lock(&sb->s_type->i_mutex_key#8); lock(&mm->mmap_lock); rlock(&sb->s_type->i_mutex_key#8); *** DEADLOCK *** This seems to be exacerbated (as we haven't seen these syzbot reports before that) by the recent: 777a856 ("lib/buildid: use __kernel_read() for sleepable context") To make this safe, we need to grab file refcount while VMA is still locked, but other than that everything is pretty straightforward. Internal build_id_parse() API assumes VMA is passed, but it only needs the underlying file reference, so just add another variant build_id_parse_file() that expects file passed directly. [akpm@linux-foundation.org: fix up kerneldoc] Link: https://lkml.kernel.org/r/20260129215340.3742283-1-andrii@kernel.org Fixes: ed5d583 ("fs/procfs: implement efficient VMA querying API for /proc/<pid>/maps") Signed-off-by: Andrii Nakryiko <andrii@kernel.org> Reported-by: <syzbot+4e70c8e0a2017b432f7a@syzkaller.appspotmail.com> Reviewed-by: Suren Baghdasaryan <surenb@google.com> Tested-by: Suren Baghdasaryan <surenb@google.com> Reviewed-by: Shakeel Butt <shakeel.butt@linux.dev> Cc: Alexei Starovoitov <ast@kernel.org> Cc: Daniel Borkmann <daniel@iogearbox.net> Cc: Eduard Zingerman <eddyz87@gmail.com> Cc: Hao Luo <haoluo@google.com> Cc: Jiri Olsa <jolsa@kernel.org> Cc: John Fastabend <john.fastabend@gmail.com> Cc: KP Singh <kpsingh@kernel.org> Cc: Martin KaFai Lau <martin.lau@linux.dev> Cc: Song Liu <song@kernel.org> Cc: Stanislav Fomichev <sdf@fomichev.me> Cc: Yonghong Song <yonghong.song@linux.dev> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 43151f8 upstream. An issue was triggered: BUG: kernel NULL pointer dereference, address: 0000000000000000 #PF: supervisor read access in kernel mode #PF: error_code(0x0000) - not-present page PGD 0 P4D 0 Oops: Oops: 0000 [#1] SMP NOPTI CPU: 15 UID: 0 PID: 658 Comm: bash Tainted: 6.19.0-rc6-next-2026012 Tainted: [O]=OOT_MODULE Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), RIP: 0010:strcmp+0x10/0x30 RSP: 0018:ffffc900017f7dc0 EFLAGS: 00000246 RAX: 0000000000000000 RBX: 0000000000000000 RCX: ffff888107cd4358 RDX: 0000000019f73907 RSI: ffffffff82cc381a RDI: 0000000000000000 RBP: ffff8881016bef0d R08: 000000006c0e7145 R09: 0000000056c0e714 R10: 0000000000000001 R11: ffff888107cd4358 R12: 0007ffffffffffff R13: ffff888101399200 R14: ffff888100fcb360 R15: 0007ffffffffffff CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000000000000000 CR3: 0000000105c79000 CR4: 00000000000006f0 Call Trace: <TASK> dmemcg_limit_write.constprop.0+0x16d/0x390 ? __pfx_set_resource_max+0x10/0x10 kernfs_fop_write_iter+0x14e/0x200 vfs_write+0x367/0x510 ksys_write+0x66/0xe0 do_syscall_64+0x6b/0x390 entry_SYSCALL_64_after_hwframe+0x76/0x7e RIP: 0033:0x7f42697e1887 It was trriggered setting max without limitation, the command is like: "echo test/region0 > dmem.max". To fix this issue, add check whether options is valid after parsing the region_name. Fixes: b168ed4 ("kernel/cgroup: Add "dmem" memory accounting cgroup") Cc: stable@vger.kernel.org # v6.14+ Signed-off-by: Chen Ridong <chenridong@huawei.com> Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit b4d37cd upstream. When deassigning a KVM_IRQFD, don't clobber the irqfd's copy of the IRQ's routing entry as doing so breaks kvm_arch_irq_bypass_del_producer() on x86 and arm64, which explicitly look for KVM_IRQ_ROUTING_MSI. Instead, to handle a concurrent routing update, verify that the irqfd is still active before consuming the routing information. As evidenced by the x86 and arm64 bugs, and another bug in kvm_arch_update_irqfd_routing() (see below), clobbering the entry type without notifying arch code is surprising and error prone. As a bonus, checking that the irqfd is active provides a convenient location for documenting _why_ KVM must not consume the routing entry for an irqfd that is in the process of being deassigned: once the irqfd is deleted from the list (which happens *before* the eventfd is detached), it will no longer receive updates via kvm_irq_routing_update(), and so KVM could deliver an event using stale routing information (relative to KVM_SET_GSI_ROUTING returning to userspace). As an even better bonus, explicitly checking for the irqfd being active fixes a similar bug to the one the clobbering is trying to prevent: if an irqfd is deactivated, and then its routing is changed, kvm_irq_routing_update() won't invoke kvm_arch_update_irqfd_routing() (because the irqfd isn't in the list). And so if the irqfd is in bypass mode, IRQs will continue to be posted using the old routing information. As for kvm_arch_irq_bypass_del_producer(), clobbering the routing type results in KVM incorrectly keeping the IRQ in bypass mode, which is especially problematic on AMD as KVM tracks IRQs that are being posted to a vCPU in a list whose lifetime is tied to the irqfd. Without the help of KASAN to detect use-after-free, the most common sympton on AMD is a NULL pointer deref in amd_iommu_update_ga() due to the memory for irqfd structure being re-allocated and zeroed, resulting in irqfd->irq_bypass_data being NULL when read by avic_update_iommu_vcpu_affinity(): BUG: kernel NULL pointer dereference, address: 0000000000000018 #PF: supervisor read access in kernel mode #PF: error_code(0x0000) - not-present page PGD 40cf2b9067 P4D 40cf2b9067 PUD 408362a067 PMD 0 Oops: Oops: 0000 [#1] SMP CPU: 6 UID: 0 PID: 40383 Comm: vfio_irq_test Tainted: G U W O 6.19.0-smp--5dddc257e6b2-irqfd #31 NONE Tainted: [U]=USER, [W]=WARN, [O]=OOT_MODULE Hardware name: Google, Inc. Arcadia_IT_80/Arcadia_IT_80, BIOS 34.78.2-0 09/05/2025 RIP: 0010:amd_iommu_update_ga+0x19/0xe0 Call Trace: <TASK> avic_update_iommu_vcpu_affinity+0x3d/0x90 [kvm_amd] __avic_vcpu_load+0xf4/0x130 [kvm_amd] kvm_arch_vcpu_load+0x89/0x210 [kvm] vcpu_load+0x30/0x40 [kvm] kvm_arch_vcpu_ioctl_run+0x45/0x620 [kvm] kvm_vcpu_ioctl+0x571/0x6a0 [kvm] __se_sys_ioctl+0x6d/0xb0 do_syscall_64+0x6f/0x9d0 entry_SYSCALL_64_after_hwframe+0x4b/0x53 RIP: 0033:0x46893b </TASK> ---[ end trace 0000000000000000 ]--- If AVIC is inhibited when the irfd is deassigned, the bug will manifest as list corruption, e.g. on the next irqfd assignment. list_add corruption. next->prev should be prev (ffff8d474d5cd588), but was 0000000000000000. (next=ffff8d8658f86530). ------------[ cut here ]------------ kernel BUG at lib/list_debug.c:31! Oops: invalid opcode: 0000 [#1] SMP CPU: 128 UID: 0 PID: 80818 Comm: vfio_irq_test Tainted: G U W O 6.19.0-smp--f19dc4d680ba-irqfd #28 NONE Tainted: [U]=USER, [W]=WARN, [O]=OOT_MODULE Hardware name: Google, Inc. Arcadia_IT_80/Arcadia_IT_80, BIOS 34.78.2-0 09/05/2025 RIP: 0010:__list_add_valid_or_report+0x97/0xc0 Call Trace: <TASK> avic_pi_update_irte+0x28e/0x2b0 [kvm_amd] kvm_pi_update_irte+0xbf/0x190 [kvm] kvm_arch_irq_bypass_add_producer+0x72/0x90 [kvm] irq_bypass_register_consumer+0xcd/0x170 [irqbypass] kvm_irqfd+0x4c6/0x540 [kvm] kvm_vm_ioctl+0x118/0x5d0 [kvm] __se_sys_ioctl+0x6d/0xb0 do_syscall_64+0x6f/0x9d0 entry_SYSCALL_64_after_hwframe+0x4b/0x53 </TASK> ---[ end trace 0000000000000000 ]--- On Intel and arm64, the bug is less noisy, as the end result is that the device keeps posting IRQs to the vCPU even after it's been deassigned. Note, the worst of the breakage can be traced back to commit cb21073 ("KVM: Pass new routing entries and irqfd when updating IRTEs"), as before that commit KVM would pull the routing information from the per-VM routing table. But as above, similar bugs have existed since support for IRQ bypass was added. E.g. if a routing change finished before irq_shutdown() invoked kvm_arch_irq_bypass_del_producer(), VMX and SVM would see stale routing information and potentially leave the irqfd in bypass mode. Alternatively, x86 could be fixed by explicitly checking irq_bypass_vcpu instead of irq_entry.type in kvm_arch_irq_bypass_del_producer(), and arm64 could be modified to utilize irq_bypass_vcpu in a similar manner. But (a) that wouldn't fix the routing updates bug, and (b) fixing core code doesn't preclude x86 (or arm64) from adding such code as a sanity check (spoiler alert). Fixes: f70c20a ("KVM: Add an arch specific hooks in 'struct kvm_kernel_irqfd'") Fixes: cb21073 ("KVM: Pass new routing entries and irqfd when updating IRTEs") Fixes: a0d7e2f ("KVM: arm64: vgic-v4: Only attempt vLPI mapping for actual MSIs") Cc: stable@vger.kernel.org Cc: Marc Zyngier <maz@kernel.org> Cc: Oliver Upton <oupton@kernel.org> Link: https://patch.msgid.link/20260113174606.104978-2-seanjc@google.com Signed-off-by: Sean Christopherson <seanjc@google.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 5e8a3d0 upstream. Oneway transactions sent to frozen targets via binder_proc_transaction() return a BR_TRANSACTION_PENDING_FROZEN error but they are still treated as successful since the target is expected to thaw at some point. It is then not safe to access 't' after BR_TRANSACTION_PENDING_FROZEN errors as the transaction could have been consumed by the now thawed target. This is the case for binder_netlink_report() which derreferences 't' after a pending frozen error, as pointed out by the following KASAN report: ================================================================== BUG: KASAN: slab-use-after-free in binder_netlink_report.isra.0+0x694/0x6c8 Read of size 8 at addr ffff00000f98ba38 by task binder-util/522 CPU: 4 UID: 0 PID: 522 Comm: binder-util Not tainted 6.19.0-rc6-00015-gc03e9c42ae8f #1 PREEMPT Hardware name: linux,dummy-virt (DT) Call trace: binder_netlink_report.isra.0+0x694/0x6c8 binder_transaction+0x66e4/0x79b8 binder_thread_write+0xab4/0x4440 binder_ioctl+0x1fd4/0x2940 [...] Allocated by task 522: __kmalloc_cache_noprof+0x17c/0x50c binder_transaction+0x584/0x79b8 binder_thread_write+0xab4/0x4440 binder_ioctl+0x1fd4/0x2940 [...] Freed by task 488: kfree+0x1d0/0x420 binder_free_transaction+0x150/0x234 binder_thread_read+0x2d08/0x3ce4 binder_ioctl+0x488/0x2940 [...] ================================================================== Instead, make a transaction copy so the data can be safely accessed by binder_netlink_report() after a pending frozen error. While here, add a comment about not using t->buffer in binder_netlink_report(). Cc: stable@vger.kernel.org Fixes: 6374034 ("binder: introduce transaction reports via netlink") Signed-off-by: Carlos Llamas <cmllamas@google.com> Reviewed-by: Alice Ryhl <aliceryhl@google.com> Link: https://patch.msgid.link/20260122180203.1502637-1-cmllamas@google.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit fc6f36e ] Fix race condition where PTP periodic work runs while VSI is being rebuilt, accessing NULL vsi->rx_rings. The sequence was: 1. ice_ptp_prepare_for_reset() cancels PTP work 2. ice_ptp_rebuild() immediately queues PTP work 3. VSI rebuild happens AFTER ice_ptp_rebuild() 4. PTP work runs and accesses NULL vsi->rx_rings Fix: Keep PTP work cancelled during rebuild, only queue it after VSI rebuild completes in ice_rebuild(). Added ice_ptp_queue_work() helper function to encapsulate the logic for queuing PTP work, ensuring it's only queued when PTP is supported and the state is ICE_PTP_READY. Error log: [ 121.392544] ice 0000:60:00.1: PTP reset successful [ 121.392692] BUG: kernel NULL pointer dereference, address: 0000000000000000 [ 121.392712] #PF: supervisor read access in kernel mode [ 121.392720] #PF: error_code(0x0000) - not-present page [ 121.392727] PGD 0 [ 121.392734] Oops: Oops: 0000 [#1] SMP NOPTI [ 121.392746] CPU: 8 UID: 0 PID: 1005 Comm: ice-ptp-0000:60 Tainted: G S 6.19.0-rc6+ #4 PREEMPT(voluntary) [ 121.392761] Tainted: [S]=CPU_OUT_OF_SPEC [ 121.392773] RIP: 0010:ice_ptp_update_cached_phctime+0xbf/0x150 [ice] [ 121.393042] Call Trace: [ 121.393047] <TASK> [ 121.393055] ice_ptp_periodic_work+0x69/0x180 [ice] [ 121.393202] kthread_worker_fn+0xa2/0x260 [ 121.393216] ? __pfx_ice_ptp_periodic_work+0x10/0x10 [ice] [ 121.393359] ? __pfx_kthread_worker_fn+0x10/0x10 [ 121.393371] kthread+0x10d/0x230 [ 121.393382] ? __pfx_kthread+0x10/0x10 [ 121.393393] ret_from_fork+0x273/0x2b0 [ 121.393407] ? __pfx_kthread+0x10/0x10 [ 121.393417] ret_from_fork_asm+0x1a/0x30 [ 121.393432] </TASK> Fixes: 803bef8 ("ice: factor out ice_ptp_rebuild_owner()") Signed-off-by: Aaron Ma <aaron.ma@canonical.com> Tested-by: Sunitha Mekala <sunithax.d.mekala@intel.com> (A Contingent worker at Intel) Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit bbf4a17 ] syzbot reported a kernel BUG in fib6_add_rt2node() when adding an IPv6 route. [0] Commit f72514b ("ipv6: clear RA flags when adding a static route") introduced logic to clear RTF_ADDRCONF from existing routes when a static route with the same nexthop is added. However, this causes a problem when the existing route has a gateway. When RTF_ADDRCONF is cleared from a route that has a gateway, that route becomes eligible for ECMP, i.e. rt6_qualify_for_ecmp() returns true. The issue is that this route was never added to the fib6_siblings list. This leads to a mismatch between the following counts: - The sibling count computed by iterating fib6_next chain, which includes the newly ECMP-eligible route - The actual siblings in fib6_siblings list, which does not include that route When a subsequent ECMP route is added, fib6_add_rt2node() hits BUG_ON(sibling->fib6_nsiblings != rt->fib6_nsiblings) because the counts don't match. Fix this by only clearing RTF_ADDRCONF when the existing route does not have a gateway. Routes without a gateway cannot qualify for ECMP anyway (rt6_qualify_for_ecmp() requires fib_nh_gw_family), so clearing RTF_ADDRCONF on them is safe and matches the original intent of the commit. [0]: kernel BUG at net/ipv6/ip6_fib.c:1217! Oops: invalid opcode: 0000 [#1] SMP KASAN PTI CPU: 0 UID: 0 PID: 6010 Comm: syz.0.17 Not tainted syzkaller #0 PREEMPT(full) Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 10/25/2025 RIP: 0010:fib6_add_rt2node+0x3433/0x3470 net/ipv6/ip6_fib.c:1217 [...] Call Trace: <TASK> fib6_add+0x8da/0x18a0 net/ipv6/ip6_fib.c:1532 __ip6_ins_rt net/ipv6/route.c:1351 [inline] ip6_route_add+0xde/0x1b0 net/ipv6/route.c:3946 ipv6_route_ioctl+0x35c/0x480 net/ipv6/route.c:4571 inet6_ioctl+0x219/0x280 net/ipv6/af_inet6.c:577 sock_do_ioctl+0xdc/0x300 net/socket.c:1245 sock_ioctl+0x576/0x790 net/socket.c:1366 vfs_ioctl fs/ioctl.c:51 [inline] __do_sys_ioctl fs/ioctl.c:597 [inline] __se_sys_ioctl+0xfc/0x170 fs/ioctl.c:583 do_syscall_x64 arch/x86/entry/syscall_64.c:63 [inline] do_syscall_64+0xfa/0xf80 arch/x86/entry/syscall_64.c:94 entry_SYSCALL_64_after_hwframe+0x77/0x7f Fixes: f72514b ("ipv6: clear RA flags when adding a static route") Reported-by: syzbot+cb809def1baaac68ab92@syzkaller.appspotmail.com Closes: https://syzkaller.appspot.com/bug?extid=cb809def1baaac68ab92 Tested-by: syzbot+cb809def1baaac68ab92@syzkaller.appspotmail.com Signed-off-by: Shigeru Yoshida <syoshida@redhat.com> Reviewed-by: Fernando Fernandez Mancera <fmancera@suse.de> Link: https://patch.msgid.link/20260204095837.1285552-1-syoshida@redhat.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>

apopple added 2 commits September 29, 2015 14:50

bt/ipmi: Add Aspeed BT IPMI host driver

446301e

This patch adds a simple device driver to expose the iBT interface on Aspeed chips as a character device (/dev/bt). Signed-off-by: Alistair Popple <alistair@popple.id.au>

apopple merged this pull request into openbmc:dev Sep 29, 2015

Kenthliu mentioned this pull request Nov 5, 2015

Kernel crash caused by network setting. #17

Closed

Provide feedback

Saved searches

Use saved searches to filter your results more quickly

Fix GPIO Kconfig bug & add BT host driver#1

Fix GPIO Kconfig bug & add BT host driver#1
apopple merged 2 commits intoopenbmc:devfrom
apopple:openbmc_dev

apopple commented Sep 29, 2015

Uh oh!

Reviewers

Assignees

Labels

Projects

Milestone

Development

Uh oh!

1 participant

Conversation

apopple commented Sep 29, 2015

Uh oh!

Reviewers

Assignees

Labels

Projects

Milestone

Development

Uh oh!

1 participant